如果故障 LED 为红色,则show power命令输出将报告电源模块出现故障。 Switch#show idprom power-supplyslot-number Switch#show module 如果show module 命令输出显示的信息为“模块没有足够的电源”,请查看电源规格,了解相应的电源规范。电源本身可能有问题。 交流输入电源故障排除 为帮助确定电源子系...
Switch-sp#show bootBOOT variable = bootdisk:s72033-advipservicesk9_wan-mz.122-18.SXF7.bin,1; CONFIG_FILE variable does not exist BOOTLDR variable does not existConfiguration register is 0x2101 這會導致交換機啟動以前的映像,無論運行配置中的BOOT變數配置如何。要解決此問題,請發出命令switch(config...
Pressing and holding the mode button does nothing for me, i have read other threads and the solution that has worked for me is after power cycling the switch just start pressing the mode button multiple times until you see "switch:"" 11 Helpful Reply niraj551 Level 1 In response to ...
display transceiver diagnosis interface Ten-GigabitEthernet0/1/5 注释:查看H3C设备0/1/5端口光衰值,主要查看Current diagnostic parameters:中的Rx power(dBM):-2.62 3、思科设备查看光衰值命令: show interface eth1/43 transceiver detials | include dBm 注释:查看思科设备1/43端口光衰值,主要查看Rx Power行的...
show environment [clock|power|fan|temperature]命令查看交换机clock、电源、风扇、温度传感器这些模块的运行状态。show environment后面可以接一个参数,用于查看指定模块的状态。 示范: MDS9222i-1# show environment Clock: -始终模块。每个交换机有两个,一个active,一个standby。两个状态都是正常。
H3C接口获取IP地址有以下方式: 1,通过手工指定 2,通过BOOTP分配得到IP地址 3,通过DHCP分配得到IP地址 一个接口只能有一个主IP地址,新配置的主IP地址将覆盖原来的主IP 当接口被配置为通过BOOTP和DHCP获取IP后,该接口不能在分配从IP地址 举例,同一VLAN中有个两个IP段,172.16.1.0和172.16.2.0 <switch ip 配置 端...
Switch#show cisco dhcp 中继配置 原创2013-03-19 08:35:311298阅读 Mongodb副本集配置 选择服务器: 1.首先考虑mongodb的热数据大小,最好可以包含在内存大小范围之内,然后确定内存大小 2.选用raid级别:raid10(官方推荐) 3.选择文件系统:xfs、ext4(官方推荐) 4.硬盘:最好ssd(有几个公司可以满足呢?sas也不错)...
5.1. Default Gateway on a Switch // 各个interface的信息, ip地址, 查看子网掩码等(以及vty, console的密码等) show running-config // 管道 show run | include mask show run | begin mask // 查看是否使能每个interfaces, no shutdown show ip interface brief show ipv6 interface brief // 查看route...
对于Cisco光纤交换机,可以通过命令:show version 获取到交换机的版本信息,如下所示: switch(config)# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html Copyrig...
The Cisco ® SGE2010P 48-Port Gigabit Switch (Figure 1) allows you to expand your network securely. Web-based configuration of the switch is secured using SSL. The Cisco SGE2010P is optimized for maximum system availability, with fully redundant stacking, redundant power options, and dual ...