switch(config-if)#no shutdown ②、配置接口全双工 switch(config-if)#duplex full ;设置该端口为全双工 switch(config-if)#description up_to_mis ;设置该端口描述为 up_to_mis switch(config-if)#end ;退回到特权模式 ③、接口描述 switch(config)#interface fastethernet 0/1 switch(config)#description o...
switch(config)#interface fastethernet 0/1 switch(config-if)#speed 100 switch(config-if)#no shutdown ②、配置接口全双工 switch(config-if)#duplex full ;设置该端口为全双工 switch(config-if)#deion up_to_mis ;设置该端口描述为 up_to_mis switch(config-if)#end ;退回到特权模式 ③、接口描述 sw...
Router(config-if)#ip address 192.168.1.1 255.255.255.0输入接口IP地址和掩码 Router(config-if)#no shutdown路由器接口默认都为shutdown,所以要启用,就要打no shutdown 注意:默认情况下如果没有设置虚拟终端密码是无法从远端进行telnet的,远端进行telnet时候会提示设置login密码。许多新手会认为no login是无法从远端...
Switch(config)#interface gigabit ethernet 7/29Switch(config-if)#switchport%Command rejected: Cannot convert port. Maximum number of interfaces reached. Output of idb: AMC440E-SAS01#show idbMaximum number of Software IDBs 12000. In use 11999. HWIDBs SWIDBs Active 218 220 Inactive 11779 11779 To...
switchname MDS9148-1 interface mgmt0 ip address 192.168.10.12 255.255.255.0 gatway 192.168.10.1 no shutdown ssh key rsa 1024 force feature ssh feature telnet feature http-server system default switchport shutdown system default switchport trunk mode off ...
如果show isdn status命令輸出指示第1層狀態為DEACTIVATED,則E1線路的物理連線存在問題。如果線路為管理性關閉,請使用no shutdown命令重新啟動介面。 確保第2層處於MULTIPLE_FRAME_ESTABLISHED狀態。這是第2層所需的狀態,表示正在交換第2層幀並且已完成第2層初始化。
Switch-lib(config-if)no shutdown Switch-lib(config-if)ip address 【 6】 配置交换机的管理地址 Switch-lib(config-if)exit Switch-lib(config)ip default-gateway167.11.45.1 Switch-lib(config)vtp domain lib Switch-lib(config)vtp mode transparent Switch-lib(config)exit Switch-libvlan data Switch-lib...
I am confused about the “no keepalive” and “no shutdown” command on different interface type on router. In serial interface, the status is down/down. But in ethernet interface, it is up/up. Could anyone please clear me? And can this reason apply wit...
switch(config-if)# no cdp enable 为了查看Cisco邻接设备的CDP通告信息: switch# show cdp interface [type modle/port] switch# show cdp neighbors [type module/port] [detail] 在基于CLI的交换机上启用和浏览CDP信息: switch(enable) set cdp {enable|disable} module/port ...
I am confused about the “no keepalive” and “no shutdown” command on different interface type on router. In serial interface, the status is down/down. But in ethernet interface, it is up/up. Could anyone please clear me? And can this reason apply with Catalyst too? T...