switch(config-if)# ipv6 enable Automatically configures an IPv6 link-local address on the interface while also enabling the interface for IPv6 processing. The link-local address can be used only to communicate with nodes on the same link. Step 4 switch(config-if)# no shutdown ...
This interface configuration is for a Cisco IOS IPv6 router implementing stateful DHCPv6 on a local Switch: ipv6 unicast-routing ipv6 dhcp pool IPV6_DHCPPOOL address prefix 2001:db8:5:10::/64 domain-name cisco.com dns-server 2001:db8:6:6::1 interface...
Switch(config)#hostname XXX Switch(config)#enable secret 123456 Router(config)#enable secret level 1 pass123 Router(config)#enable secret level 15 pass123 Switch(config)#ip address 192.168.1.1 255.255.255.0---设置交换机的管理IP地址 Switch(config)#ip default-gateway 192.168.1.254---设置交换机的...
no ip address shutdown negotiation auto ! interface Service-Engine0/1/0 ! interface Serial0/1/0:15 encapsulation hdlc isdn switch-type primary-net5 isdn timer T310 60000 isdn overlap-receiving isdn incoming-voice voice isdn T309-enable isdn sending-complete no cdp enable ! interface Service-Eng...
一、地址与IP 地址。 DCS 实验步骤 时,AM可以使用no am enable上的源 路由交换 休闲 神州数码 DCS交换机 原创2009-11-16 14:48:363354阅读12 (神州数码)动态实现配置mac地址与端口绑定 最近在学校帮忙整理设计学校的实训实验文档,也同时有了可以接触神州数码的网络设备,顺便再整理一些配置命令放到博客上希望可以给一...
OSPF单区域配置 实验名称:OSPF单区域配置 实验拓扑: 实验配置步骤: 交换部分: Switch1 Enable Vlan database Vlan 10 name magi Exit 将vlan10加入到端口f0/2 Conf t Int fa0/2 Switchport mode access Switchport access vlan 10 center target color ...
(一)使能口令(enable password),口令以明文显示 (二)使能密码 (enbale secret),口令以密文显示 两者一般只需要配置其中一个,如果两者同时配置时,只有使能密码生效. Switch.> /*用户直行模式提示符 Switch.>enable /*进入特权模式 Switch.# /*特权模式提示符 ...
Router>enable Router# 步骤2:进入全局配置模式 进入全局配置模式,可以配置路由器的全局参数和接口设置。在特权模式下,输入以下命令: 代码语言:javascript 复制 Router# configure terminalRouter(config)# 步骤3:创建扩展访问列表 在全局配置模式下,输入以下命令创建一个扩展访问列表: ...
2.登陆到交换机,然后在enable状态下输入如下命令来完成IOS的保存: switch#copy flash tftp Source IP address or hostname [171.68.206.171]? Source filename []? cat6000-sup2k8.7-1-1.bin Destination filename [cat6000-sup2k8.7-1-1.binn]?
We are always considering the link-local address in its entirety, i.e., the complete /128 IPv6 address, as a host address - no subnet IDs or prefixes or any of that stuff. For example: Switch#ping FE80::214:6AFF:FE96:CA4E Output Interface: Vlan709Type escape sequence to abort....