2.设置思科type9密码(最强密码) 2.交换机ssh仅允许办公机登录 3.交换机用snmp端口添加到zabbix监控 2.所有接口配置全双工 5.配置port channel二层链路聚合 0.设置管理IP 设置vlan 设置vlanif 1.设置成ssh登录 所有用户密码均应加密存放 secret=秘密 switch(config)#service password-encryption #启用密码加密服务 ...
enable secret命令用於設定授予對Cisco IOS系統的特權管理訪問許可權的口令。必須使用enable secret命令,而不是更舊的enable password命令。其enable password命令使用弱加密演算法。 如果未設定任何enable secret且為控制檯tty線路配置了口令,則可以使用控制檯口令來接收特權訪問,即使是從遠端虛擬tty (vty)會話也是如此。...
5 Specifies an ENCRYPTED secret will follow 建议不要采用enable password pass_sting密码,破解及其容易! 2、设置对交换机明文密码自动进行加密隐藏 switch(config)#service password-encryption 3、为提高交换机管理的灵活性,建议权限分级管理并建立多用户 switch(config)#enable secret level 7 5 pass_string7 /7级...
输入命令进入全局配置模式: Switch> enable Switch# configure terminal Switch(config)# 1. 设置交换机名称: Switch(config)#hostname CISCO 2. 设置enable密码 CISCO(config)#enable secret 123456 3. 设置交换机时间 CISCO#clock set 10:00:00 22 May 2024 4. 设置vlan CISCO(config)#vlan 10 CISCO(config-...
switch(conf)#hostnameaptch2950 aptech2950(conf)# enable passwordcisco 05配置使能密码enable secretciscolab以cicso为例 switch>enable switch#configure terminal switch(conf)#hostname aptch2950 aptech2950(conf)# enble secret ciscolab 06创建多个VLAN ...
Switch#renameflash:config.oldflash:config.text > 执行copyflash:config.textsystem:running-config, 此命令是拷贝配置文件到当前系统中,也就是恢复原来交换机配置。 使用enable password或enable secret命令重新设置密码。 使用write memory命令保存配置,重启交换机。
and 9 forenable secret. If you specify an encryption type, you must provide an encrypted password—an encrypted password that you copy from another switch configuration. Secret encryption type 9 is more secure, so we recommend that you...
switch(enable) set vlan vlan-num mod-num/port-list 9. 在基于IOS的交换机上配置VLAN中继线: switch(config)# interface interface mod/port switch(config-if)# switchport mode trunk switch(config-if)# switchport trunk encapsulation {isl|dotlq} ...
cisco switch enable ssh and telnet 一、连接拓扑 PT3000 Boot Loader (PT3000-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1) Compiled Mon 22-Jul-02 18:57 by miwang Cisco WS-CSwitch-PT (RC32300) processor (revision C0) with 21039K bytes of memory. ...
cisco switch enable ssh and telnet 一、连接拓扑 PT3000 Boot Loader (PT3000-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1) Compiled Mon 22-Jul-02 18:57 by miwang Cisco WS-CSwitch-PT (RC32300) processor (revision C0) with 21039K bytes of memory. ...