switchxxxxxx#clear ipv6 dhcp clientvlan 100 ipv6 address dhcp To enable DHCP for an IPv6 client process and acquire an IPv6 address on an interface, use theipv6 address dhcpcommand in Interface Configuration mod
switchxxxxxx(config-dhcp)#dns-server10.12.1.99 domain-name To specify the domain name for a DHCP client, use thedomain-namecommand in DHCP Pool Network Configuration mode or in DHCP Pool Host Configuration mode. To remove the domain name, use thenoform of this command. Syntax domain-...
switch #config t (进入配置模式)Enter configuration commands?one per line. End with CNTL/Z.switch ?config?#interface vlan1 (配置 VLAN1)switch ?config-if?#ip helper-addres 9、s (指定 DHCP 服务器的地址, 即路由器的地址)ghq?config-if?#interface vlan2 (配置 VLAN2)ghq?config-if?#ip helper...
switch #config t (进入配置模式) Enter configuration commandsone per line. End with CNTL/Z. switch config #interface vlan1 (配置VLAN1) switch config-if #ip helper-address 192.168.1.4(指定DHCP服务器的地址,即路由器的地址) ghqconfig-if #interface vlan2 (配置VLAN2) ghqconfig-if #ip helper-ad...
Enter configuration commands, one per line. End with CNTL/Z. SWITCH(config)# SWITCH(config)#host SW1 SW1(config)# SW1(config)#int e0/0 SW1(config-if)#ip add 12.1.1.2 255.255.255.0 //和R1相连的接口 SW1(config-if)# SW1(config-if)#no shutdown ...
switch(config)#interface vlan 12 switch(config-if)#ip address 172.16.60.1 255.255.255.0 VLAN12interfaceIP 接入终端设置对应VLAN的网络地址,默认网关为该VLAN的interface地址。 dhcp服务 1 .CISCO路由器的dhcp服务器功能是在ios 12.0(1)T以后出现的,这一功能的出现,使我们无需再另外配置一台DHCP server,从而降...
switch #config t （进入配置模式）Enter configuration commands�one per line. End with CNTL/Z.switch �config #interface vlan1 （配置VLAN1）switch �config-if #ip helper-address 192.168.1.4（指定DHCP服务器的地址，即路由器的地址）ghq�config-if...
The following commands will initializethe flash filesystem, and finish loading the operatingsystem software: flash_init boot switch: flash_initInitializing Flash...flashfs[0]: 554 files, 19 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 32514048flashfs[0]:...
switch #config t (进入配置模式) Enter configuration commandsone per line. End with CNTL/Z. switch config#interface vlan1 (配置VLAN1) switch config-if#ip helper-address 192.168.1.4(指定DHCP服务器的地址,即路由器的地址) ghqconfig-if#interface vlan2 (配置VLAN2) ...
switch #c onfig t (进入配置模式) Enter configuration commands one per line. End with CNTL/Z. switch config #interface vlan1 (配置VLAN1) switch config-if #ip helper-address 192.168.1.4(指定DHCP服务器的地址,即路由器的地址) ghq config-if #interface vlan2 (配置VLAN2) ...