Example 1—The following example enables the security suite feature and specifies that security suite commands are global commands only. When an attempt is made to configure security-suite on a port, it fails.
aaa' commands for 'LOCAL'...Crypto(changed): ed686f 8e2e689c 2553 7a2bd33aEnd configurationreplication Primary.Cluster unitunit-3-1 transitioned from DISABLED SECONDARY 两台设备(unit-1-1和unit3-1)均在其集群日志中显示: firepower show clusterinfo trace | include retainNov 03 21:...
Enterconfigurationcommands,oneperline.EndwithCNTL/Z. switch(config)#switchnameswitchswitch(config)# switch(config)#interfacemgmt0 switch(config-if)#ipadress15switch(config-if)#noshutdown interfacemgmt0表示的是交换机的管理端口。 2.2.配置VSAN 接下来配置VSAN switch#configt switch(config)#vsandatabaseswi...
Meraki access & aggregation switches are all managed through an elegant, intuitive cloud interface, freeing administrators to spend less time on configuration and more time on meeting business needs.To set up a Meraki switch, just plug it in; there’s no need for repetitive, command-based ...
commands 5、在端口启用dotlX 命令格式:dotlxport—controlauto ㈢、配置交换机 Radius通信 1、在交换机上定义radius服务器参 数 命令格式:radius server h0st {hostnamelip—address;auth-portport- numberacct-portportnumbe rkeykey～ string 2、配置与RadiUS重传参数(可选 ...
cisco命令大全 1. switch配置命令 (1)模式转换命令 用户模式---特权模式,使用命令"enable"特权模式---全局配置模式,使用命令"config t"全局配置模式---接口模式,使用命令"interface+接口类型+接口号"全局配置模式---线控模式,使用命令"line+接口类型+接口号"注:用户模式:查看初始化的信息.特权模式:查看所有信息、...
24Switch210.0.20.2/24PC-PTPC4具体配置过程:首先在模拟器中搭建好实验拓扑环境(注意搭建过程中要选择正确的电缆类型,交换机之间应该使用交叉线,交换机与主机之间应该使用直通线)SWITCH1switchl〉enableswitchl#configt/进入特权模式Enterconfigurationcommands,oneperline.EndwithCNTL/Z.switchl(config)#vlan10switch1(...
Chapter 2 Cisco IOS Commands for the Catalyst 6500 Series Switches with the Supervisor Engine 32 PISA show catalyst6000 show catalyst6000 To display the information about the Catalyst 6500 series switch, use the show catalyst6000 command.
端口配置状态把物理端口变成三层口配置 IP地址和掩码激活端口退出验证配置保存配置配置举例如下:Switch# configure terminalEnter configuration commands, one per line.End with CNTL/Z.Switch(config)# interface gigabitethernet0/2Switch(config-if)# no switchportSwitch(config-if)# ip address 1 Switch(config-if...
1、启动流程图 1）ROM 监控模式：路由器已启动但是没有加载任何IOS IOS，提示符为：，提示符为：，提示符为：>>或rommon 1> 2）启动模式：启动Flash 里含有最小化IOS 启动程序，提示符为：启动程序，提示符为：router router router（（boot boot））> 3）用户执行模式：成功加载启动了一份完整的IOS 代码，...