Enter configuration commands, one per line. End with CNTL/Z. SWITCH(config)# 通过ACL访问控制,仅允许从某个固定IP地址访问交换机 配置ACL策略 SWITCH(config)# ip access-list extended only-permit-IP permit ip host 192.168.1.254 any 应用ACL策略 SWITCH(config)#line vty 0 15 access-class only-permi...
Enter configuration commands,one per line.EndwithCNTL/Z.Switch(config)# ps: configure terminal意为配置终端,单词较长,可采用以下解决办法: tab键自动补全 简写成conf t 4.全局配置模式 代码语言:javascript 代码运行次数:0 运行 AI代码解释 特权用户模式下的命令提示符:(configure)+#Switch(config)#?Configure...
Switch>enSwitch#configure terminalEnter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname L3L3(config)#ip routingL3(config)#vtp mode serverDevice mode already VTP SERVER. L3(config)#vtp domain ciscoChanging VTP domain name from NULL to cisco L3(config)#vlan 2L3...
Configure the switch to which your access point is to attach. See the Cisco Wireless Controller Configuration Guide for the release you are using, for additional information. Set the Cisco Wireless Controller as the master so that new access points always join with it. Make sure DHCP is enable...
Switch(config-if)#no switchport Switch(config-if)#ip address 10.20.1.1 255.255.255.0 Switch(config-if)#no shutdown Switch(config-if)#end Switch# Switch#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#line vty 0 15 Switch(config-line)#login...
access-enable Create a temporary Access-List entry clear Reset functions connect Open a terminal connection disable Turn off privileged commands disconnect Disconnect an existing network connection enable Turn on privileged commands exit Exit from the EXEC ...
switch(config-line)#access-class 18 in /在线路模式下调用前面定义的标准ACL 18 switch(config-line)#exec-timeout 5 0 /设置不执行命令操作的超时时间，单位为分钟和秒 switch(config-line)#authorization commands 7 vty-in /调用设置的授权列表vty-in switch(config-line)#authorization commands ...
Switch(vlan)# exit 将端口分配给一个 VLAN comfigure terminal 进入配置状态 inerftoce intertae-id 进入要分配的端口 swilchport mode access 定义二层口 swilchport access vlan vlan-id 把端口分配给某一个VLAN 例: Switch# comnfigure terminal Enter ofiguration commands, one per line. End with CNTLZ...
switchport trunk native vlan vlan-id#定义trunk口的许可vlan列表switchport trunk allowed vlan {all|[add|remove|except]} vlan-list例:switchport trunk allowed vlan remove2#VTPSwitch>en Switch#conf tEnter configuration commands, one per line. EndwithCNTL/Z. ...
4.8.1 配置Switch 4.8.2 配置ISE 4.8.3 配置Cisco AnyConnect客户端 4.8.4 验证配置 4.8.5 配置文件 5 MAC地址认证对接配置举例 5.1 组网需求 5.2 使用版本 5.3 MAC地址认证配置步骤与验证 5.3.1 配置Switch 5.3.2 配置ISE 5.3.3 验证配置 5.4 配置文件 6 Portal认证对接配置举例 6.1 组网需求 6.2 使用版本...