Switch#(config)#interface fastethernet 3/1Switch#(config-if)#spanning-tree guard root ! 附註:適用於執行Cisco IOS系統軟體的Catalyst 6500/6000的Cisco IOS軟體版本12.1(3a)E3將此命令從spanning-tree rootguard變更為spanning-tree guard root。執行Cisco IOS系統軟體的Catalyst 4500/4000在所有版本中使用spanning...
Switch(config)# interface fastethernet 0/8 Switch(config-if)# spanning-tree rootguard Switch(config-if)# ^Z *Mar 15 20:15:16: %SPANTREE-2-ROOTGUARD_CONFIG_CHANGE: Rootguard enabled on port FastEthernet0/8 VLAN 1. Switch# Quelle est la différence entre STP BPDU Guard et STP Root ...
Switch(config-if)#spanning-tree bpdufilter enable/---在不启用Port Fast特性的情况下启用BPDU Filtering---/ 一般层2网络的SP可能会有多条达到客户网络的连接.为了防止客户交换机偶然成为根桥,可以在连接到客户交换机的端口上使用Root Guard特性来避免这一问题的发生.那个根保护的端口会强制成为指定端口(即不允许...
SC(config)#spanning-tree portfast bpduguard default // 全局启用bpdu防护 SWITCH D: SD(config)#interface fast 0/3-8 //配置端口3-8 SD(config-if)# spanning-tree portfast //3-8号端口启用portfast特性。 SD(config-if)#spanning-tree bpduguard enable //3-8号端口启用bpdu 防护 //SD(config-if)...
My core switch is also root of spanning-tree, i use Rapid-pvst. On this switch, in global configuration i can see :spanning-tree portfast bpduguard defaultspanning-tree portfast bpdufilter default This commands are necessary ? not ?thanks a lot I have this problem too Labels: LAN Switching...
1根防护switch(config)#int f0/0switch(config-if)#spanning-tree guard root 2 BPDU Guardswitch(config)# spanning-tree portfast bpduguard default或者switch(config)#int f0/0switch(config-if)#spanning-tree bgduguard enable 3 BPDU filterswitch(config)#spanning-tree portfast bpdufilter default或switch(...
STP(生成树协议,Spanning Tree Protocol)就是解决冗余拓扑出现的问题。STP 基本思路是阻断一些交换机接口,构建一棵没有环路的转发树,让具有冗余结构的网络在故障时自动调整网络的数据转发路径。本篇记录学习计算机网络重点知识:生成树协议(STP),详细步骤将从认识到实践,使用Cisco Packet Tracer 完成STP综合练习。同时,也...
Do not enable Loopguard on vPC (disabled by default) Do not enable Bridge Assurance on vPC 为了便于操作和快速诊断,以下建议适用于vPC环境中的STP Configure the Spanning Tree Protocol root for all VLAN on vPC primary device (spanning-tree vlan 100-102 root primary) Configure the Spanning Tree Pro...
vPC peer-link运行spanning-tree port type network ,因为bridge assurance默认在链路上激活; 配置root guard在DCI vPC上。STP root必须保持在数据中心两端的本地; vPC域之外不能存在环路; 不要在数据中心之间使用三层连接(换句话说没有Layer 3 over vPC) 不要在DCI vPC上使用bridge assurance; 如果两个数据中心之...
RootGuard的配置范围:层,分布层的下行接口。开启RootGuardconfig-if# spanning-tree guard root验证rootguard(查看某处跟不一致状态的接口)#show spanning-tree inconsistentports环路防护:交换机之间的链路出现了单向B 20、PDU故障,会导致交换机无法继续接收BPDU,老化时间到期之后阻塞的端口会过度到侦听,侦听学习转发状态...