Switch(config)# interface fastethernet 0/8 Switch(config-if)# spanning-tree rootguard Switch(config-if)# ^Z *Mar 15 20:15:16: %SPANTREE-2-ROOTGUARD_CONFIG_CHANGE: Rootguard enabled on port FastEthernet0/8 VLAN 1. Switch# Quelle est la différence entre STP BPDU Guard et STP Root ...
Switch#(config)#interface fastethernet 3/1Switch#(config-if)#spanning-tree guard root ! 附註:適用於執行Cisco IOS系統軟體的Catalyst 6500/6000的Cisco IOS軟體版本12.1(3a)E3將此命令從spanning-tree rootguard變更為spanning-tree guard root。執行Cisco IOS系統軟體的Catalyst 4500/4000在所有版本中使用spanning...
Switch(config-if)#spanning-tree bpdufilter enable/---在不启用Port Fast特性的情况下启用BPDU Filtering---/ 一般层2网络的SP可能会有多条达到客户网络的连接.为了防止客户交换机偶然成为根桥,可以在连接到客户交换机的端口上使用Root Guard特性来避免这一问题的发生.那个根保护的端口会强制成为指定端口(即不允许...
SB(config)#spanning-tree vlan 3 SB(config)#spanning-tree vlan 3 priority 4096 SB(config)#spanning-tree vlan 3 root primary SB(config)#spanning-tree vlan 2,4 priority 9152 SB(config)#spanning-tree vlan 2,4 root secondary SWITCH C: SD(config)#spanning-tree mode pvst //设置生成树的协议 ...
1根防护switch(config)#int f0/0switch(config-if)#spanning-tree guard root 2 BPDU Guardswitch(config)# spanning-tree portfast bpduguard default或者switch(config)#int f0/0switch(config-if)#spanning-tree bgduguard enable 3 BPDU filterswitch(config)#spanning-tree portfast bpdufilter default或switch(...
Root guard will only prevent the Port channel 30 to be a root port. The best approach on this case is force your switch to be the root on vlan 734. spanning-tree vlan 734 root primary Best regards.ı|ı.ı|ı. If This Helps, Please Rate .ı|ı.ı|ı. View solution ...
Do not enable Loopguard on vPC (disabled by default) Do not enable Bridge Assurance on vPC 为了便于操作和快速诊断,以下建议适用于vPC环境中的STP Configure the Spanning Tree Protocol root for all VLAN on vPC primary device (spanning-tree vlan 100-102 root primary) Configure the Spanning Tree Pro...
在接口下面命令为:spanning-tree bpduguard enable 2. BPDU过滤 通过启用BPDU过滤,能够防止交换机在启用PORTFAST特征的接口上发送BPDU。在启用BPDU过滤的情况下,如果配置了PORTFAST的接口收到BPDU,那么它将立即丢弃PORTFAST状态,在这种情况中,交换机在各个接口上禁用PORTFAST BPDU过滤,而STP将从端口向所连接的设备中继续发...
STP(生成树协议,Spanning Tree Protocol)就是解决冗余拓扑出现的问题。STP 基本思路是阻断一些交换机接口,构建一棵没有环路的转发树,让具有冗余结构的网络在故障时自动调整网络的数据转发路径。本篇记录学习计算机网络重点知识:生成树协议(STP),详细步骤将从认识到实践,使用Cisco Packet Tracer 完成STP综合练习。同时,也...
STP(Spanning Tree Protocol,生成树协议)为物理上冗余的网络拓扑结构保持逻辑无环拓扑结构提供了相应的实现机制。桥接域中的所有设备都要运行生成树算法以发现拓扑结构并计算去往根网桥(root bridge)的最佳路径。生成树进程会将冗余网络链路会设置为阻塞状态,从而防止出现二层环路。