I'm working on switch 1 and a having a problem with seeing the Vlans I created. Show vlan only shows default vlan1 and the other vlans that come with the IOS example fddi token ring etc. but not the one I created. When I did a show vtp status I got this switch# show vtp statu...
To display VLAN information, use the show vlan command in privileged EXEC mode. show vlan [all | brief | id vlan-id | name name [ifindex] | ifindex] Syntax Description all (Optional) Displays all VLAN information. brief (Optional) Displays only a single line for each VLAN, naming ...
比如,show version命令可以查看设备的硬件版本和软件版本信息;show interface可以查看设备的接口信息等等。 3. 配置设备:在对设备进行配置的过程中,管理员需要使用命令行来完成。比如,配置IP地址、子网掩码、默认网关等网络参数;配置VLAN、端口安全;配置路由表等等。 4. 保存配置:完成对设备的配置后,管理员需要使用相应...
Switch(config)#hostname SwA (4)给交换机划分VLAN(需要在特权模式下进行) 1 2 3 4 5 SwA(config)#vlan 100 SwA(config-vlan)#exit SwA(config)#vlan 200 SwA(config-vlan)#exit SwA(config)# (5)查看划分的VLAN是否生效(在特权模式下进行查看) 1 SwA#show vlan 2、1-6端口给VLAN100,9-16端口给VL...
The show vlan command does not display these VLANs unless you create it using the vlan command. SUMMARY STEPS 1. config t 2. vlan configuration {vlan-id} DETAILED STEPS Command or ActionPurpose Step 1 config t Example: switch# config t switch(config)#...
show ip interface brief 查看接口的谪要信息 banner motd # +信息 + # 配置路由器或交换机的描素信息 description+信息 配置接口听描素信息 vlan database 进入VLAN数据库模式 vlan +vlan号+ 名称 创建VLAN switchport access vlan +vlan号 为VLAN为配接口 ...
command,butnotforthe1900switch TheshowCDPinterfacedisplaysaspecificinterfacethat enablesCDP Showcdpneighbordisplaysdirectconnectedneighbordevices andtheirdetailedinformation TheshowcdpneighbordetaildisplaystheIPaddressandthe IOSversionandtype,andincludesalltheinformation ...
步骤3使用show running-config命令检查是否存在重叠的IP地址。 步骤4若存在,则改变IP地址。 Show interfaces status err-disabled 查看路由器/交换机是否存在逻辑错误的端口 有错误的。 Show mac address-table 查看路由器/交换机端口上的MAC地址表 Show vlan brief 查看VLAN的详细数据(vlan号和划分的端口)©...
Port Vlans allowed and active in management domain Fa0/3 1 Port Vlans in spanning tree forwarding state and not pruned Fa0/3 none If you want to see which interfaces are configured as “Trunk” ports, the above command will show you just this. As shown above, port Fa0/3 is configure...
尝试对CiscoIOSXE进行检查,以查看是否仍然在默认VLAN中配置了任何端口。Output = net_connect.send_command ('show int status', use_textfsm=true) if i["vlan"] == "1": else: print ('Complian 浏览15提问于2022-10-14得票数1 回答已采纳