Solved: Hi gurus, Below are my logging configurations R2#show log Syslog logging: enabled (12 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message
show processes cpu history命令 如果交換機未重新載入或未進行切換,請在服務中斷的72小時內運行show processes cpu history命令,以檢視事件發生時是否出現CPU使用率較高的情況。 CoPP和HWRL 如果CPU使用率高是過去中斷的根本原因,並且您懷疑中斷是由網路流量觸發的,您可以使用CoPP和HWRL(硬體速率限制器)...
要找出属于特定进程ID (PID)的所有线程的CPU使用情况,请使用show process cpu detail<pid>命令(在NX-OS版本6.2x中提供)。 show processes cpu history命令 使用此命令可显示过去60秒、60分钟和72小时的CPU使用情况。请务必检查平均CPU使用率(#)和峰值(*)。 switch# show processes cpu history 1 131 12...
第一步:启动log logging on 注:By de fault, the logging level is set to 3 (error). 默认log的级别为3(error) 第二步:设置log级别 logging trap severity_level (1-7) 第三步:检查log设置 show logging 二:测试log输出 通过下面几个步骤测试log信息输出: 第一步:log信息发送到console口。 logging con...
If you choose as I do to disable this outdated feature the command is “no ntp allow mode control”. This command will then show up in the running-config as “no ntp allow mode control 0”. I added this command to an IOS router that was both receiving time from an external time sour...
Log in to the listed device through the CLI and use the show version | include Device Manager command to determine the configured Cisco ASDM release. If this output reports a Cisco ASDM release earlier than Release 7.18.1.152, then the warning message is legitimate and an attack less likely....
andthename oftheroutertowhichtheinterfaceisconnected Showflashdisplaysfilesinflashmemory Theshowframe-relayImisetstheLMItypeontheserial interface Showframe-relaymapshowsstaticanddynamicmappingof networklayerstoPVC Theshowframe-relayPVCdisplaystheconfiguredPVCandDLCI numbersontherouter Theshowhistorydisplaysthelast...
cisco#show ip bgp su | b Ne Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 10.10.10.2 4 65002 8 10 126 0 0 00:04:30 2 7. 原因分析 如上面现象所阐述,该故障最终原因为 cisco 设备上收到了 forti 传来的用于建立 bgp 的 10.10.10.2/32 位主机路由,而 cisco 上是 ...
第一步:启动log logging on 注:By de fault, the logging level is set to 3 (error). 默认log的级别为3(error) 第二步:设置log级别logging trap severity_level (1-7) 第三步:检查log设置show logging 二:测试log输出 通过下面几个步骤测试log信息输出: ...
switch(config)#showvlanid31 VLANNameStatusPorts 31cp_packetactive VLANTypeMTU 5enet1500 RemoteSPANVLAN Disabled PrimarySecondaryTypePorts switch(config)#copyrunstart [###]100% switch(config)# FeatureHistoryfortheVSMDomain Thistableonlyincludesupdatesforthosereleasesthathaveresultedinadditionstothefeature....