区分器用于扩展IP地址,并允许您确定其所属的VPN。 rd [VPN route distinguisher] 使用以下命令设置BGP扩展社区的导入和导出属性。这些属性用于过滤导入和导出过程。 route-target {export | import | both} [target VPN extended community] 使用ip vrf forwarding [table name]命令配置各个接口的转发详细信息,并记得...
show ip bgp network命令显示给定网络的BGP路由表中的条目。 RouterR1#show ip bgp vpnv4 rd 1100:1001 10.30.116.0/23BGP routing table entry for 1100:1001:10.30.116.0/23, version 26765275Paths: (9 available, best #6, no table)Advertised to update-groups: 1 2 3 (65001 64955 65003) 65089, (...
erase startup-config//清空所有配置 show hist 查看历史输入 sh pri //查看权限等级 sh run //显示配置信息 sh ip interface brief //查看所有接口状态、地址信息 sh ip route rip //通过rip学习到的路由 sh vtp status //查看vtp参数 sh vtp pass //查看vtp密码 sh ip nat tr//查看nat转换 sh ip ac...
In the context of VPNv6 (address-family vpnv6), it is common to use IPv4 addresses as the BGP neighbor addresses, even though the routes exchanged may be IPv6 routes. The IPv4 address is used for the BGP peering, and the IPv6 routes are carried within the VPNv6 address family. ...
sh ip bgp vpnv4 vrf ABC su 如果你起的VRF 叫ABC ,而且地址簇是在ipv4下，这样show出来的就是bgp的建立情况。
If IGP is used in CE-PE, then all the BGP entries in the VRF routing table will always be coming from VPNv4, right? BGP entries in the routing tables will be always from remote , won't them? I check if I use IGP CE-PE the show ip bgp VPNV4 vrf show both local and remote ...
ip address 80.1.2.1 255.255.255.0 duplex full ! router bgp 1000 no synchronization bgp log-neighbor-changes redistribute connected neighbor 80.1.2.2 remote-as 100 no auto-summary ! end [R2] R2#show run ! version 12.4 ! hostname R2
3、PE上创建VRF(VPNA),PE与CE间通过OSPF互联(进程号:1); 4、R2与R4两台PE间建立MP-IBGP邻接关系,(BGP AS234) 5、完成PE-CE间的路由重发布; 二、配置信息: R1 R1#show run ! hostname R1 ! ip cef ! interface Loopback0 ip address 1。1.1.1 255.255。255。255 ip ospf network point—to-poin...
Address family VPNv4 Unicast: advertised and received 当BGP邻居建立好之后,此时R2已经能够学习到VPNV4路由,如下: R2#show ip route vrf vrf1 Routing Table: vrf1 Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF ...
DMVPN over different FVRF and IVRF Hi,I'm trying to get DMVPN (mGRE over IPSEC) to establish over different FVRF and IVRF on the hub side.Just for clarity, hub IP is 10.1.1.1, spoke's is 10.2.2.2 (obviously I have routing between the 2, they can ping each other etc)If I...