以下输出是在启用模式下执行的show ip interfacebriefcommand的典型输出: 3600#show ip interface briefInterface IP-Address OK? Method Status Prol BRI0/0 unassigned YES NVRAM administratively down dow FastEthernet0/0 172.16.99.20 YES NVRAM up up Serial0/0 unassigned YES NVRAM down dow Serial0/0.1 un...
如果您在fxos模式下执行show run interface mgmt0,则在该接口下执行shutdown force。同样,请勿使用此命令作为关闭的参考: FPR4115-2-1(fxos)# show run interface mgmt0 !Command: show running-config interface mgmt0 !Time: Tue May 5 14:19:42 2020 version 5.0(3)N2(4.81) interface mgmt0 shut...
vsan 100 interface fc1/1-48 end 查看端口所属vsan show interface brief 查看光口wwn show flogi database 设置别名 config t device-alias database device-alias name UNITY_SPA_P4 pwwn 50:06:01:62:49:e0:2d:3c device-alias name UNITY_SPB_P4 pwwn 50:06:01:6a:49:e0:2d:3c device-alias name...
One of the most useful and popular commands used on Cisco devices is the “show interface” command. It can be very useful at troubleshooting connectivity issues and physical port issues, check the status of physical ports, watch how much traffic is passing through the interface, which IP addre...
S1#conf t S1(config)#interface vlan 1 S1(config-if)#no shutdown (this command will activate the interface) S1(config-if)#Ctrol+C (=2*exit) S1#show interface brief 2. Config Passwords 2.1. Secure User EXEC Mode Access. To secure user EXEC mode access, enter line console ...
1、Show running-config 查看 路由器/交换机 的运行配置 2、Show ip interface brief 查看 路由器/交换机 所有端口的状态 端口及线路协议状态 错误原因 解决方案 GigabitEthernetx is up, line protocol is up 此状态为正确状态 GigabitEthernetx is down, line protocol is down 路由器未检测到载波信号 1.传输...
Cisco的网m际操作系统(IOS:Internetwork Operating Syste),IOS配置通常是通过基于文本的命令行接口(Command Line Interface,CLI)进行的。 二、路由其基本操作 1、基本操作模式 1)用户模式 Router> #通常可以查看统计信息 Router>logout #退出用户模式 2)特权模式 ...
show ip interface brief 查看接口的谪要信息 R1(config)#banner motd # +信息 + # 配置路由器或交换机的描素信息 R1(config-if)#description+信息 配置接口听描素信息 vlan database 进入VLAN数据库模式 vlan +vlan号+ 名称 创建VLAN switchport access vlan +vlan号 为VLAN为配接口 ...
4.插上网线，连接电脑（电脑端口设置为自动获取IP地址）5.进入配置页面：10.0.0.1---用户名及密码都是cisco 交换机密码：cisco1 talent密码：wisdri 6.电脑需要安装USB驱动 7.启用talent登录 输入交换机密码cisco1 Switch>enable Password:Using driver version 4 for me Switch>show vlan VLAN Name Status ...
show optical-inform brief interface xgei-0/1/0/2 总结: 1.如上列举了各厂家设备查看端口的光衰(光功率值)命令,你会用了吗? 2.命令我们是知道了,但是你知道返回的Rx值在正常范围吗,当你遇到光衰值异常或者过大时我们如何快速定位问题和解决问题呢!!!