配置多播转发 多播转发 典型的多播设置 多播操作 多播注册 多播地址属性 定义多播属性 MAC 组地址 IP 多播组地址 IGMP 侦听 MLD 侦听 IGMP/MLD IP 多播组 多播路由器端口 定义 "Forward All"多播 定义未注册的多播设置 思科精睿 (Cisco Small Business) 300 系列管理...
After powering down the router I can login, butnaturally it is now using the startup config - lacking the IP address I attempted. I have the same result changing the default IP on vlan 1, or any other IP add, change, or adjustment attempt via either interface. Because of this I assume...
发出命令后,重新启动交换机,否则show interface status module <module number>命令的输出显示上行链路端口处于非活动状态。 Cisco IOS 软件版本 12.2(25)SG 支持在 Catalyst 4500 交换机上同时使用 10 千兆以太网和千兆以太网 SFP 上行接口。 注意:Catalyst 4503、4506 和 4507R 系列交换机上会自动启用此功能。 Ca...
Solved: Hi all, I am having a tough time configuring a new Cisco SG300-28PP 28, it is default on L2 mode , i have tried to change the default ip 192.168.1.254 to a different subnet 10.10.10.254 to match my local LAN and for me to manage the switch
Cisco SG300 – Configure DHCP Relay to allow DHCP server to support multiple subnets By default DHCP works via broadcasting on the local subnet and therefore is limited to being able to provide IP addresses for devices on its subnet only. In modern day networks this is a serious limitation ...
Management Interface Default Router: 网关 这个随上面的地址,不一定要存在的网关地址。反正要跟着上面的网段而改的。 Management Interface VLAN Identifier (0 = untagged): 输入 VLAN tag,默认为 0 Management Interface Port Num [1 to 1]: 1 Management Interface DHCP Server IP Address: 输入你的大二层下...
思科(CISCO)企业级网络配件会议办公语音IP电话机 3905电源适配器CP-3905-PWR-CN= 15+条评论 思科(CISCO)企业级网络配件语音视频会议终端 CS-MIC-TABLE-J=麦克风TTC5-14 100+条评论 思科(CISCO)GLC-SX-MMD千兆多模LC-LC接口模块 1+条评论 思科(CISCO)原装 双芯LC接口光纤模块SFP波长 1310nm千兆单模10公里GLC...
Cisco ASA default configurationThe DHCP server is enabled on the ASA How to Upgrade License for an ASA Failover Pair What's Cisco ASA inside VLAN 1 default IP and interfaceThe VLAN 1 IP address and mask are 192.168.1.1 and 255.255.255.0 ...
A proxy server : 192.168.1.1. All the connections are going through this Server, everything is working fine if the ip range is 192.168.1.XXX Now, when i changed the ip range from 192.168.1.XXX to 192.168.2.XXX im not able to access network, Note: default gateway is the proxy server...
ip source-route ip cef ! ! no ip dhcp use vrf connected ip dhcp excluded-address 10.1.0.1 10.1.0.149 ip dhcp excluded-address 10.1.0.200 10.1.0.254 ! ip dhcp pool net_dhcp import all network 10.1.0.0 255.255.255.0 default-router 10.1.0.1 lease 0 0 5 ! ! no ip domain lookup ip do...