要为WLC物理接口设置双工设置,请使用config port physicalmode {all | port} {100h | 100f | 10h | 10f}命令。 此命令将指定的或所有前面板 10/100BASE-T 以太网端口设置为 10 Mbps 或 100 Mbps 的专用半双工或全双工运行模式。注意,在为端口手动配置任何物理模式之前,您必须使用 config port au...
However, I also had one of the new Cisco SG300-10P switches in my possession for a recent project of ours. I decided to hook up the same POE devices to this switch. ALL POE devices were recognized and worked! No need to skip a port. And it didn't matter what ...
A.Configure the switch port, to which the WLC is connected, as an IEEE 802.1Q trunk port. Make sure that only the necessary VLANs are allowed on the switch. Usually, the management and the AP-Manager interface of the WLC are left untagged. This means that they assume the native VLAN o...
My suggestion is to use port span on the switch and analize the packets with wireshark. We need to know where the communication stops. If the Phone is not asking or if dhcp is not responding or yet if both are doing their Jobs but somthing else happens. 0 Helpful Reply enkli...
42、 Switch-1(config-if)# switch virtual link 1配置交换ID1使用该逻辑接口Switch-1(config-if)# no shutdown开启逻辑接口Switch-2(config)# interface port-channel 20 启动逻辑接口 Switch-2(config-if)# switch virtual link 2配置交换ID2使用该逻辑接口Switch-2(config-if)# no shutdown开启逻辑接口Swit...
如果show port显示已连接或 show interfaces 显示“up/ line protocol up (connected)”,但您看到其中一个命令的输出中错误数量在增加,请参阅“了解 CatOS 和 Cisco IOS 的特定端口和接口计数器输出”,或本文档的“常见端口和接口问题”部分以获得故障排除建议。
Port SAS RAID IOP348 1.2GHz Processor Controller Card <br>HighPoint RocketRAID4320 8 Port SAS RAID IOP348 1.2GHz Processor Controller Card <br>HITACHI HDS Tagmastore WMS100 SAN Storage System DF700-RKS Controller Processor <br>HMI Hunstville Microsystems 8051DE Control Processor <br>HONEYWELL 620-...
最小采购量:1 主营产品:ABB AB 供应商:厦门润星贸易有限公司 更多优质供应商> 所在地:中国 福建 厦门 联系人:谢先生 您的联系方式已覆盖全网,展示在其他同类产品页面 联系商家 点此询价 QQ咨询 QQ咨询 买家还在看 < > 优质商家推荐 我也要出现在这 ...
Port State (local only)---Gi1/4/47 Link dn Gi2/4/47 -VSS系统运行维护-启动维护命令可以通过reload命令来重新启动整个VSS,包括两个机箱;可以通过命令redundancy reload peer来只重启备机箱与备引擎;可以通过命令redundancy force-switchover来进行主备的强行切换;强制切换的结果是原来的主设备会重新启动,这个...
在连接到Meraki交换机/网络的CiscoSG-200交换机上配置VLAN 、、、 Meraki端口被配置为使用本机VLAN10的中继端口;允许的VLAN: all将Meraki交换机上的端口配置为使用本机VLAN1的中继端口,并且Cisco交换机仍然可以使用VLAN10中的静态IP。当我将Meraki交换机上的端口设 ...