I have a connection on IP 192.168.1.21, Subnet 255.255.255.0 - this is on the default VLAN1 on the switch. I need to route this to IP 10.0.3.101, Subnet 255.255.252.0 - which is set up on VLAN2 on the switch. I have set the switch to Layer 3 via console. Could someone pl...
Can you vlan just by using the 3508's/2950's switches without a router (I want 3 vlans on 1 network segment). Is this possible, and if it is could someone point me towards some documentation that would give me specifics on how to set this up ? What ...
1、* vian 配置思路(access、Trunk)(1) 创建 Vian在基于IOS的交换机上配置静态VLAN:switch# vla n databaseswitch(vla n)# vlan vlan-num n ame vlan-n ameswitch(vla n)# exitswitch# con figure terim inalswitch(c on fig)# in terface in terface module/nu mberswitch(c on fig-if)# ...
2950(config-vlan)# name VLAN_name 创建VLAN 2950(config-if)# switchport mode access 指定连接是接入链路连接 2950(config-if)# switchport access vlan VLAN_# 指定VLAN是接入链路连接 4000>(enable) set vlan VLAN_# name VLAN_name 配置VLAN 4000>(enable) set vlan VLAN_# slot_#/port_#-port_# 为...
一、虚拟局域网(VLAN) 二、交换机间链路(ISL)协议 三、虚拟局域网(VLAN)路由实例 第一章:路由器配置基础 一、基本设置方式 一般来说,可以用5种方式来设置路由器: 1.Console口接终端或运行终端仿真软件的微机; 2.AUX口接MODEM,通过电话线与远方的终端或运行终端仿真软件的微机相连; ...
L2_Switch(config)#interface vlan 1L2_Switch(config-if)#ip address 10.10.0.2 255.255.255.0L2_Switch(config-if)#no ip directed-broadcast L2_Switch(config-if)#no ip route-cache L2_Switch(config-if)#exit L2_Switch(config-if)#ip default-gateway 10.10.0.1!-- (Optional) Set the VTP Mode. ...
1.不同的vlan 不同vlan需要路由 在路由的端口设置多个IP段 2.查看端口名字 SWA#sh vlan default Active F0/1, F0/2, F0/3, F0/4, F0/5, F0/6, F0/7, F0/8 f是端口名子 default Active Gi/1, Gi0/2, Gi0/3, Gi0/4, Gi0/5, Gi0/6, Gi0/7, Gi0/8 ...
To set up VLAN support between the SUP and PPCs, complete tasks in these sections: Setting Up the SUP Setting Up the PPCs Setting Up the SUP For PPCs to receive traffic from the SUP, complete these tasks on the SUP: Set up a VLAN for each PPC. Assign the VLANs to a VL...
4000>(enable) set port duplex slot_#/port_# full|half 设置交换机接口双工模式 4000>(enable) clear config all 删除NVRAM中的配置信息 4000>(enable) erase all 删除FLASH中的内容 4000>(enable) show flash 显示FLASH中的内容 4000>(enable) show cam [count] dynamic|static|permanent|system [vlan_#]...
set vlan set vtp show cam show config show flash show interface show ip permit show ip route show log show mac show module show port show system show users show version show vlan show vtp telnet 配置说明 1.R1 2.R2 3.R3 4.R4