不同于 ip default-gateway 命令,可以在 Cisco 路由器上已启用 IP 路由时使用 ip default-network。当您配置ip default-network时,路由器会将要安装到该网络的路由视为路由器上的最后选用网关。对于用 ip default-network 配置的每个网络,如果路由器有一个路由到该网络,则该路由被标记为候选默认路由。以下网络图显...
rommon 2>set IP_ADDRESS=192.168.247.10rommon 3>set IP_SUBNET_MASK=255.255.0.0rommon 4>set DEFAULT_GATEWAY=172.20.52.35rommon 5>set TFTP_SERVER=198.51.100.2 步骤3 输入set 命令以确保保存设置,然后启动系统 示例: rommon 6>setrommon 7>boot
配置交换机网关:Switch(config)#ip default-gateway 网关 switch(config)#int vlan 1 设置ip地址和掩码: switch(config-if)#ip address 10.65.1.3 255.255.0.0 设置switch的网关: switch(config)#ip defaule-gateway 10.65.1.9 查看当前配置: switch#sh run 8.清除思科所有配置 SWA#del vlan.dat SWA#reload 9...
On a few of my remote FTD boxes, they don't seem to have a default gateway defined in the config and I don't know how to set one on them. I'm not able to ping a few of them from my FMC, so I'm not sure why they are reporting as online. Any thoughts on...
ip default-gateway 192.168.1.254 //设置默认路由,供其他网段访问 8.恢复出厂设置 en erase startup-config delete flash:vlan.dat reload 重启 9.设置errdisable (config)#errdisable recovery cause all //开启errdiable 恢复的原因 (config)#errdisable recovery interval 300 //errdisable后300秒恢复 ...
switch(enable) set ip route default gateway 42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令: router(config)# interface interface number router(config-if)# mls rp vlan-id vlan-id-num 43. 在路由处理器启用MLSP: router(config)# mls rp ip ...
ip default-gateway172.16.1.1为模拟PC的略由器配置一个默认网关 配置一条静态路由 Branch(config)#ip route 172.16.1.0 255.255.255.0 e0/1 192.168.1.1 //告诉路由器,去往172.16.1.0/24这个网络应该将数据从e0/1接口转发出去,交给192.168.1.1这个设备 ...
config 清除原有配置 3.capwap ap ip address ***(ip-addr) ***(subnet-mask) 配置AP静态ip地址和掩码 4.capwap ap controller ip address ***(ip-addr) 配置AP所注册控制器地址 5.capwap ap hostname ***(ap-hostname) 配置AP的名称 6.capwap ap ip default-gateway ***(ip-addr) 配置AP的网关...
oDefault gateway oSimple Network Management Protocol (SNMP) community string oRole in the radio network oSSID This example configures these parameters: oIP address:10.0.0.1 oHost name:AP1200 oSSID:CISCO123 Note:SSIDs are unique identifiers that identify a WLAN network. Wireless devices use SSIDs...
* - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set C 192.168.1.0/24 is directly connected, Vlan1 C 192.168.2.0/24 is directly connected, Vlan2 C 192.168.3.0/24 is directly connected, Vlan3 ...