If i give show mac-address address and enter ( mac-address of the pc) it says no entry found.If i give show mac-address incl address (mac-address of the pc) then it gives output of which the pc is connected. Also if i give only the command as show mac-address then it give the...
mac-address-table Configure the MAC address table 配置地址表 no Negate a command or set its defaults 否定命令或设置默认值 ntp Configure NTP 配置NTP parameter-map Parameter map 参数图 parser Configure parser 配置分析器 policy-map Configure QoS Policy Map 配置服务质量策略图 port-channel EtherChannel...
The active router sources hello packets from its configured IP address and the HSRP virtual MAC address. The standby router sources hellos from its configured IP address and the burned-in MAC address (BIA). This use of source addressing is necessary so that HSRP routers can correctly identify e...
Router(config)# router <路由协议rip | igrp | eigrp | ospf | is-is等> [自主系统号] Router(config-router)# network <直接相连的要用此路由协议的网络号> Router(config-router)# network <直接相连的要用此路由协议的网络号> *路由信息协议RIP Router(config)# router rip Router(config-router)# net...
--- The debug output shows that the router R2 can ping router R3's Link-Local address. 本地鏈路地址僅特定於該本地網路。路由器可以擁有相同的本地鏈路地址,並且直連網路可以彼此通訊,而不會有任何衝突。對於全局單播地址,情況並非如此。可路由的全局單播地址在網路中必須是唯一的。show ipv6 interface ...
2PIM协议配置PIM-DM基本配置激活多播路由Router(config)#ipmulti 14、cast-routingPIM-DM配置在接口模式下输入Ippimdense-mode【例如】ipmulticast-routinginterfaceFastEthernet0/1ipaddressippimstate-refreshorigination-interval60ippimdense-modePIM-SM基本配置激活多播路由Router(config)#ipmulticast-routing需在所有路由...
1. router> 路由器处于用户命令状态,这时用户可以看路由器的连接状态,访问其它网络和主机,但不能看到和更改路由器的设置内容。 2. router# 在router>提示符下键入enable,路由器进入特权命令状态router#,这时不但可以执行所有的用户命令,还可以看到和更改路由器的设置内容。
设置如下:Router1:hostname router1username router2 password xxxinterface Serial0ip address 192.200.10.1 255.255.255.0clockrate 1000000ppp authentication chap!Router2:hostname router2username router1 password xxxinterface Serial0ip address 192.200.10.2 255.255.255.0ppp authentication chap!
由于管理需要,公司决定要把DHCP时候的IP和MAC地址进行绑定。 拓扑如下: 1.配置dhcp服务器: service dhcp ip dhcp pool cisco network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 255.255.255.0 下面的pc获取测试dhcp配置正常。 2.设置PC获取指定的ip地址 ...
To configure an IPv4 default gateway on a switch, use the ip defult-gateway ip-address global configuration command. The ip-address that is configured is the IPv4 address of the local router interface connected to the switch(路由器连接这个switch的interface的ip就是这个switch的默认Gateway, ).编辑...