Router(config-if)# ipv6 address ipv6_address_prefix/prefix_length [eui-64] Theipv6 unicast-routingcommand globally enables IPv6 and must be the first IPv6 command executed on the router. The ipv6 address command assigns the prefix, the length, and the use of EUI-64 to assign the interf...
Router(config-if)#exit Router(config)#interface s0/3/1 Router(config-if)#ipv6 enable Router(config-if)#ipv6 address 2023::1B:2/112 Router(config-if)#exit 2、配置EIGRP 2-1、启用ipv6路由 Router0 Router(config)#ipv6 unicast-routing Router1 Router(config)#ipv6 unicast-routing Router2 Ro...
//配置隧道动态路由(用RIP)Router(config)#router ripRouter(config-router)#network192.168.20.0Router(config-router)#network192.168.30.0Router(config-router)#exit ###Router 3 代码语言:javascript 复制 Router>enable Router#configure terminalRouter(config)#interfaceFastEthernet0/0Router(config-if)#ip address...
来自支持Cisco的IPv6路由器的以下Cisco IOS®配置命令用于启用SLAAC寻址和路由器通告: ipv6 unicast-routing interface Vlan20 description IPv6-SLAAC ip address 192.168.20.1 255.255.255.0 ipv6 address 2001:DB8:0:20::1/64 ipv6 enable end DHCPv6地址分配 如果已部署SLAAC,则IPv6客户端连接不需要使用DHCPv6。
步骤1.确保在全局配置模式下配置了ipv6 unicast-routing命令。 步骤2.确保本地网络中的接口配置了有效的IPv6地址。 ipv6 unicast-routing! Enable IPv6 Routing. In absence of this command ! ! the Router does not send any ICMPv6 RA packet.interface GigabitEthernet0/0/0 ...
ipv6 unicast-routingipv6 dhcp pool router prefix-delegation pool ct-prefixinterface Dialer1 description CnTel mtu 1492 ip address negotiated ip nat outside no ip virtual-reassembly in encapsulation ppp ip tcp adjust-mss 1452 dialer pool 1 dialer down-with-vInterface no cdp enable...
问题2,拨号获取到电信IPv6地址后,它会在每天更换动态IPv4公网地址的时候又会增加一个IPv6地址,那么这个IPv6之前的地址是否正常可用,如不能正常使用,怎么配置是之在更换v4地址后重新只获取一个v6地址?我的v6相关配置:ipv6 unicast-routingipv6 cefinterface Dialer1bandwidth 50000 ip address negotiated no ip ...
R3(config-if)#ipv6 enable R3(config-if)#ipv6 address 2022::1/112 R3(config-if)#exit 2、开启ipv6功能 R1 R1(config)#ipv6 unicast-routing R2 R2(config)#ipv6 unicast-routing R3 R3(config)#ipv6 unicast-routing 3、创建ospfv3,并配置router-id ...
1、在R1和R3上开启Ipv6路由能 R1(config)#ipv6unicast-routing R3(config)#ipv6unicast-routing 2、在三台路由器上配置Ipv4地址，并配置默认路由 R1(config)#interface ethernet0/0 R1(config-if)#ip address192.168.12.1255.255.255.0 R1(config-if)#no shutdown R1(config)#ip route0.0.0.00.0.0...
Which command must be globally enabled on a Cisco router to support IPv6?() A. ip routing ipv6 B. ipv6 unicast - routing C. ipv6 routing D. ip classless E. ipv6 cef 相关知识点: 试题来源: 解析 B.ipv6 unicast - routing