show processes Command router#show processes CPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0 PID Q Ty PC Runtime(ms) Invoked uSecs Stacks TTY Process 1 C sp 602F3AF0 0 1627 0 2600/3000 0 Load Meter 2 L we 60C5BE00 4 136 29 5572/6000 0 ...
在思科 7600 系列路由器上启用 Netflow NDE 时 CPU 使用率高 如果为版本7配置了NetFlow,则流由路由处理器执行,这会导致CPU使用率过高。 要排除由于NetFlow版本7而导致的CPU使用率较高的故障,请配置mls nde sender版本5,因为NetFlow导出由SP执行,这是版本5或版本9的默认值。
CPU utilization for five seconds: 90%/88%; one minute: 88%; five minutes: 87%PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process6 431973856 45106939 9576 0.47% 0.11% 0.11% 0 Check heaps332 46964436 283618948 165 0.23% 0.24% 0.23% 0 CFT Timer Proces255 115875220 60137923 1926 ...
I know its bit awkward but what I feel is since the router is connected to 100mbps switch with full duplex, the router is trying to send data at that speed but cpu is going high. Note: Due to recession all new procurement is freezed. I am trying to solve this CPU utilization problem...
Theshow process cpucommand displays Cisco IOS CPU utilization average: Router#show process cpuCPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process PID Runtime(ms) Invoked uSecs 5Sec...
Cisco CCNP TSHOOT Useful Commands to Monitor CPU Utilization Theshow processes cpucommand displays overall router CPU utilization as well as the CPU utilization of each of the processes running on the router. The output CPU utilization for the past 5 seconds, past 1 minute and past 5 ...
YH-Router#sh process cpu CPU utilization for five seconds:15%/4%;one minute:175;five minutes:19% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 1 460184 5380085 85 0.00% 0.00% 0.00% 0 NTP 2 252749536 2384205 106010 0.00% 2.35% 2.65% 0 Check Heaps ...
cisco 命令:show proc cpu 精解 Router#show proc cpu CPU utilization for five seconds: 63%/50%; one minute: 58%; five minutes: 58 % PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 1 4976 54773 90 0.00% 0.00% 0.00% 0 Load Meter...
Hello Pros, In my 3845 , i am getting high cpu usage but i am not able to find out for what reason it is so much utilized. Router1#sh processes cpu sorted CPU utilization for five seconds: 64%/61%; one minute: 63%; five minutes: 62% Not a single
使用 率较高的故障 IP 输入 - 排除由于 IP 输入进程而导致的 CPU 使用率较高的故障 IP 简单网络管理协议 (SNMP) - IP 简单网络管理协议 (SNMP) 导致 CPU 使用率较高 LC ADJ 更新程序 - What Causes High CPU Utilization in the LC Adjacency Updater Process on a Cisco 12000 Series Internet Router?(...