在router>提示符下键入enable,路由器进入特权命令状态router#,这时不但可以执行所有的用户命令,还可以看到和更改路由器的设置内容。 3. router(config)# 在router#提示符下键入configure terminal,出现提示符router(config)#,此时路由器处于全局设置状态,这时可以设置路由器的全局参数。 4. router(config-if)#; router...
在router>提示符下键入enable,路由器进入特权命令状态router#,这时不但可以执行所有的用户命令,还可以看到和更改路由器的设置内容。 3. router(config)# 在router#提示符下键入configure terminal,出现提示符router(config)#,此时路由器处于全局设置状态,这时可以设置路由器的全局参数。 4. router(config-if)#; router...
Switch(config-if)#switchport access vlan 3 Switch(config-if)#switchport mode trunk 路由器: Router(config)#int f0/0 Router(config-if)#no sh Router(config-if)#int f0/0.1 Router(config-subif)#encapsulation dot1Q 2 Router(config-subif)#ip add 192.168.1.1 255.255.255.0 Router(config-subif)#n...
在router>提示符下键入enable,路由器进入特权命令状态router#,这时不但可以执行所有的用户命令,还可以看到和更改路由器的设置内容。 3. router(config)# 在router#提示符下键入configure terminal,出现提示符router(config)#,此时路由器处于全局设置状态,这时可以设置路由器的全局参数。 4.router(config-if)#;router(co...
privilege Command privilege parameters 命令特权参数 queue-list Build a custom queue list 建立自定义队列列表 radius-server Modify Radius query parameters 修改半径查询参数 router Enable a routing process 启用路由过程 secure Secure image and configuration archival commands 安全的图像和配置档案命令 security Inf...
1、常用组播路由协议配置方法1IGMP协议配置1.1 IGMP基本设置1.1.1 配置路由器加入到一个组播组:Router(config-if)#ipigmpjoin-group1.1.2 控制某个接口下主机能够加入的组播组ipigmpaccess-groupaccess-list【例如】Router(config)#access-list1Router(config)#interfaceethernet0Router(config-if)ipigmpaccess-group1...
interfaceconfigurecommand:(界面配置命令) access-expressionBuildabridgebooleanaccessexpression arp(地址协议)Setarptype(arpa,probe,snap)ortimeout backupModifybackupparameters bandwidthSetbandwidthinformationalparameter bridge-groupTransparentbridginginterfaceparameters carrier-delaySpecifydelayforinterfacetransitions cdpCDP...
An Access Control List (ACL) is a list of rules that control and filter traffic based on source and destination IP addresses or Port numbers. This happens by either allowing packets or blocking packets from an interface on a router, switch, firewall etc.
switchport access vlan +vlan号 为VLAN为配接口 interface vlan +vlan号 进入VLAN接口模式(应用于三层交换) ip add +ip地址 为VLAN配置管理IP地址 vtp+service/tracsparent/client 配置SW的VTP工作模式 vtp +domain+域名 配置SW的VTP域名 vtp +password +密码 配置SW的密码 ...
可用Router1#moretftp://172.25.1.1/CONFIGNAME来查看TFTP服务器上的文件 1.3. 使用远端配置文件启动路由器 提问:使用一个另外的配置文件来启动路由器 回答: Router1(config)#service config Router1(config)#boot network tftpCONFIGNAME1172.25.1.1 Router1(config)#boot host tftpCONFIGNAME2172.25.1.1 ...