1、实用标准文案转载Cisco Packet Tracer静态路由配置(2011-01-12 23:05:02)转载转载原文地址:Cisco Packet Tracer 静态路由配置 作者:Koolar实验环境:Cisco Packet Tracer 5.3实验步骤:一、如图所示拖放好实验网络中的各个设备:甲 Cisco P»ci H Tracern 回二、左键单击Router0的图标,在Physical选项卡下,单击...
! This is the floating static route to the LAN. 这是R2 上的配置: hostname R2 ! interface Serial1/0 ip address 10.10.10.2 255.255.255.252 ! interface Serial2/0 ip address 10.10.20.2 255.255.255.252 ! ip route 0.0.0.0 0.0.0.0 10.10.10.1 ...
Destination/Mask Proto Pre Cost Flags NextHop Interface ……10.1.2.0/24 Static 60 0...
,在Config选项卡的左方选择 Routing的 Static ,然后在右边加入刚才所说的信息,结果如图所示:同样,对于 Routeri 来说,发往 192.168.3.0 的 Next Hop是 192.168.1.1 , 发往 192.168.5.0 的 Next Hop 是 192.168.2.2.对于 Router2 来说,发往 192.168.3.0、192.168.4.0 的 Next Hop都是 192.168.2.1.根据上边...
address网络侦测 ping hostname|IP_address路由跟踪 trace hostname|IP_address5)基本设置命令全局设置 config terminal设置访问用户及密码username username password password设置特权密码 enable secret password设置路由器名 hostname name设置静态路由 ip route destination subnet-mask next-hop启动IP路由 ip routing启动...
网络命登录远程主机telnethostnameipaddress网络侦测pinghostnameipaddress路由跟踪tracehostnameipaddress5基本设置命全局设置configterminal设置访问用户及密码usernameusernamepasswordpassword设置特权密码enablesecretpassword设置路由器名hostnamename设置静态路由iproutedestinationsubnetmasknexthop启动ip路由iprouting启动ipx路由ipx...
Yes, network ID and mask you want to reach plus exit interface or next hop IP. although not asked, enter all static routes needed to reach D to G and G to E. if u can ping those, you understand static routing. Remove those before doing step 9 Regards, ML**Please Rate All Helpful...
实验6 路由器组网及静态路由配置(Cisco Packet Tracer)(设计性实验) 1.实验目的掌握IP数据报转发的基本原理;掌握静态路由表的配置方法;进一步学习模拟软件“Cisco Packet Tracer ”初步了解Cisco系列路由器的基本配置方法(在路由器用户命令状态、特权命令状态、全局设置状态、局部设置状态等的参数配置方法);根据实验要求,...
步驟7.為區域介面配置靜態路由以實現負載均衡。導航至Routing > Static Route. 路由— 靜態路由 步驟8.按一下+ Add Route. +新增路由 步驟9.為VTI介面(本配置指南為VTI-1)建立預設靜態路由,將1作為度量值,然後按一下OK. VTI-1的預設靜態路由 步驟10.重複步驟8。如果配置了多個VTI介面。
@kennylee88 can you share the PPT you are trying after adding the static route. and from where are you tring to ping? (which PC) If you want to ping to 3.3.3.2, add below route in 2nd router. #ip route 192.168.10.0 255.255.255.0 3.3.3.1 also check below link to get an good und...