环境:Cisco Packet Tracer 5.3 设备:1 台普通 PC,1 台 2950T-24 交换机,2 台 2811 路由器。 拓扑:如下图。 4.操作步骤 步骤1:按拓扑图添加设备与连接。 步骤 2:配置路由器接口。 打开路由器的 Config配置页面,按拓扑图上的标注分别配置两个路由 器的显示名、主机名和接口 Fa0/0 的 IP 地址,并注意...
环境:Cisco Packet Tracer 5.3 设备:1 台普通 PC,1 台 2950T-24 交换机,2 台 2811 路由器。 拓扑:如下图。 4. 操作步骤 步骤1:按拓扑图添加设备与连接。 步骤2:配置路由器接口。 打开路由器的 Config配置页面,按拓扑图上的标注分别配置两个路由 器的显示名、主机名和接口 Fa0/...
Packet Tracer 8.2 added a new OSPF command(show ip ospf interface brief) to Packet Tracer 8. This major version of packet Tracer features a new SDN Network Controller which enables network devices programming through API. The SDN controller API is accessible from the host using Postman, Visual ...
Here's my compressed exercise, Luis. Perhaps you can take a look? Problems: Instructions as embedded within Packet Tracer (8.1.1.0002, MacOS Monterey 12.4) won't allow response entry (can't enter IP, Subnet Mask, Gateway for PC/Laptop).
交换机的配置: C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1) Compiled Mon 22-Jul-02 18:57 by miwang Cisco WS-C2950T-24 (RC32300) processor (revision C0) with 21039K bytes of memory. 2950T-24 starting... ...
入力インターフェイスを使用して packet-tracer コマンドを実行しているときにパケットがドロップされない場合、そのパケットは UN-NAT、ACL、NAT、IP-OPTIONS、FLOW-CREATION のようなさまざまなフェーズを通過します。その結果、「ALLOW」というメッセージが表示されます。 ファイアウォール設...
キャプチャを削除した後でも、「ERROR: TRACER: NP failed tracing packet」でパケット トレーサが失敗する CSCvi42965 ASA が「show memory」出力の下に正確な空きメモリを報告しない CSCvi45567 snmpv1&2c ホスト グループが設定されていると snmpwalk を実行できない CSCvi45807 ASA:リブ...
ciscoasa(config)#logging enable ^ % Invalid input detected at '^' marker. 0 有帮助 回复 Translator Community Manager 回复Translator 发布时间 04-19-2022 06:48 AM Hello, 与“真实”ASA相比,Packet Tracer中的ASA在命令方面非常有限。它只包含一小部分通常可用的命令。 0 有帮助 回复 Tr...
Hello, I need some help with my Cisco Packet Tracer project. I'm currently facing an issue in the LAN configuration. When I try to send packets between devices, I get pink envelopes with an “X” on them, which means the packets are not being delivered... 05-03-2025 10:46:42 AM...
CSCwi67510: FMC: Packet-tracer showing a "Interface not supported" error for VLAN interfaces CSCwi67629: Devices might change status to "missing the upgrade package" after Readiness Check is initiated CSCwi67638: FMC configured DAP rule with Azure IDP SAML attributes does not match ...