NTP Control Message queries are an outdated function of NTP that assisted in Network Management (NM) functions before better NMs were created and utilized. Unless your organization is still using NTP for NM functions the Network Security Best Practices are to completely disable them all together. I...
Restrict NTP mode 6 queries. I hope that somebody can help me. Thanks. I have this problem too Labels: Cisco Cafe 1 Reply marce1000 Hall of Fame Options 03-11-202111:36 PM - Check this thread : https://community.cisco.com/t5/other-data-center-subjec...
不會重複在show up association部分或show ntp associationdetail部分中定義的術語。 使用調試排除NTP故障 部分最常見的 NTP 問題原因如下: NTP 封包未接收。 接收到NTP資料包,但不會由Cisco IOS®上的NTP進程進行處理。 NTP 封包已處理,但錯誤的因素或封包資料造成同步化中斷。 NTP 時鐘期間手動設定。 協助隔離以...
检查NTP是否配置正确。 检查ACL是否阻止了NTP数据包。 检查到源IP或目标IP的路由问题。 未处理NTP数据包 启用debug ip packet和debug ntp packets命令后,您可以看到接收和传输的数据包,也可以看到NTP对这些数据包起作用。对于收到的每个NTP数据包(如debug ip packet所示),都有由debug ntp packets生成的相应条目。
——ntp broadcast delay: 是一个全局命令,它用于设定数据包在路由器和N T P服务器之间一个回程所需时间的估计值。 ——ntp clock-period: 这条全局命令不必输入,当使用N T P进行系统时钟同步时,路由器将自动产生这条命令。 ——ntp disable: 这条接口命令使特定接口不接收N T P包。
switch(config)#errdisable recovery interval 30 /自动恢复间隔时间为30s 四、三层交换机常用路由协议安全配置 1、RIP协议 建议不采用RIPV1,使用支持md5认证的RIPV2版本 switch(config)#key chain chain_name /设置密钥链名 switch(config-key-chain)#key 1 /设置密钥号 switch(config-key-chain)#key-...
注释 可以使用ntp source loopback0 或者ntp server 10.1.1.1 source Serial 0/0 命令来指定NTP发送的源地址。由于NTP同步的是内 部时钟,所以需要配置ntp update-calendar 来同时同步其calendar时钟 14.6. 配置NTP 冗余 提问 配置多个NTP服务器的方式来提供冗余 ...
——ntp broadcast delay: 是一个全局命令,它用于设定数据包在路由器和N T P服务器之间一个回程所需时间的估计值。 ——ntp clock-period: 这条全局命令不必输入,当使用N T P进行系统时钟同步时,路由器将自动产生这条命令。 ——ntp disable: 这条接口命令使特定接口不接收N T P包。
NTPdisable:thisinterfacecommandpreventsNTPpacketsfrom beingacceptedbyaparticularinterface. NTPmaster:thisglobalcommandisusedtoconfiguretherouter astheNTPmasterclock,onlyiftherearenoexternalNT Psourcesavailable,orfortestingpurposes. NTPpeer:theglobalcommandsynchronizesthesystemclockof ...