Detection interval time is 5 seconds Following port(s) has(have) loopback link: GigabitEthernet1/0/12 //环路来自该端口 缺省情况下,系统只在Trunk端口或Hybrid端口所属的缺省VLAN内进行环回监测,如果要对trunk或hybrid接口上的所有VLAN进行环路检测,需要使用以下命令开启多VLAN检测功能,需要注意的是,loopback-...
全局打开或者关闭环路检测功能[默认打开] [undo] loopback-detechtion enalbe 端口打开或者关闭环路检测受控功能[默认打开] [undo] loopback-detechion control enable 端口打开或者关闭环路检测受控功能[默认检测端口下所有能够通过的vlan中的环路] [undo] loopback-detection per-vlan enable 显示环路检测的状态 ...
步驟3.按一下Display Mode下拉式清單,然後選擇Advanced。 步驟4.選擇Port Management > Loopback DetectionSettings。 步驟5.選中Loopback DetectionEnable覈取方塊。 步驟6.輸入Detection Interval值。 附註:有效範圍為10至60。預設值為30。在此示例中,輸入了25。 步驟7.按一下Apply。 步驟8.(可選)按一下Save以...
Ethernet itself doesnt have a loop detection methodology, so we need a L2 or L3 based protocol to help us identify that loop. POS running HDLC or PPP can easily detect this condition at L2. SDH itself has also loop capabilities in the Sonet overhead section or actually path trace element....
步骤5.选中Loopback DetectionEnable复选框。 步骤6.输入Detection Interval值。 注意:有效范围为10到60。默认值为30。在本例中,输入25。 步骤7.单击“应用”。 步骤8.(可选)单击“保存”永久保存配置。 在端口上启用环回检测 步骤1.在环回检测端口设置表中,点击与需要配置的端口对应的单选按钮。
On top of this the VCS has the loop detection which normally detects loops such as the one described in the initial post, to prevent looping searches to consume all search resources on the VCS. Hope this helps in clarifying things a bit, Andreas 0 Helpful Reply Paulo Souza VIP A...
loopback Enable error detection on loopback pagp-flap Enable error detection on pagp-flapping 自动检测非常烦,遇到错误就会自动把端口关闭。如果不想启动错误检测,可以用命令no errdisable detect cause all来关闭。 如果想检测一部分内容,不想检测另一部分,可以用下面的命令来关闭其中的检测项目 ...
detect Error disable detection recovery Error disable recovery SW1(config)#errdisable re SW1(config)#errdisable recovery ? cause Enable error disable recovery for application interval Error disable recovery timer value SW1(config)#errdisable recovery cau ...
Detection interval time is 5 seconds Following port(s) has(have) loopback link: GigabitEthernet1/0/12 //环路来自该端口 缺省情况下,系统只在Trunk端口或Hybrid端口所属的缺省VLAN内进行环回监测,如果要对trunk或hybrid接口上的所有VLAN进行环路检测,需要使用以下命令开启多VLAN检测功能,需要注意的是,loopback-...
登录基于Web的交换机实用程序,然后选择Port Management > Loopback Detection Settings。 对于CBS 250和350系列交换机,从顶部的下拉菜单中选择Advanced设置。 第2 步 选中Loopback Detection的Enable复选框。 第3 步 在Detection Interval字段中输入值。这将设置LBD数据包之间的时间间隔(以秒为单位)。