interface GigabitEthernet1.101 no shutdown encapsulation dot1Q 101 vrf forwarding 2 ip address 192.168.66.1 no ip redirects ip directed-broadcast ip mtu 1496 ipv6 address 2001:DB8::1 ipv6 enable ip nbar protocol-discovery ip policy route-map policy_1 ip helper-address 10.8.4.5 ...
% Incomplete command. g_core(config-ext-nacl)#10 permit ip 10.105.20.13 0.0.0.0 anyg_core(config-ext-nacl)#exit g_core(config)#route-map hkbn permit 10g_core(config-route-map)#match ip address hkbng_core(config-route-map)#set ip next-hop 192.168.233.254 g_core(config)#int...
ip policy route-map net-10 ! router eigrp 1 network 172.16.0.0 ! access-list 111 permit ip 10.0.0.0 0.255.255.255 any ! route-map net-10 permit 10 match ip address 111 set interface Ethernet0/1 ! route-map net-10 permit 20 ! end 请参阅route-map 命令文档,获取有关 route-map 相关命...
But I see the counter in "show route-map" is zero. SW#sh route-map all STATIC routemaps route-map INTERNET_ONLY, permit, sequence 10 Match clauses: ip address (access-lists): 10 Set clauses: ip next-hop 192.168.70.2 Policy routing matches: 0 packets, 0 bytes DYNAMIC routemaps Als...
PBR(Policy-Based Routing) 基于策略的路由。我们都知道路由是基本目的IP地址进行转发,当一个数据包到达路由器以后,路由器默认并不查看该数据包的源IP地址,只看目的IP地址,然后查路由表,进行与运算,最后封装新的二层头部将其转发出去。而PBR则是根据IP包的源IP地址进行转发,我们可以手工定义匹配到的哪些源IP地址发...
R2(config)#ip route 192.168.19.0 255.255.255.0 10.2.19.3 R3(config)#ip route 10.1.19.0 255.255.255.0 10.2.19.2 R3(config)#ip route 172.16.19.0 255.255.255.0 10.2.19.2 R3(config)#ip route 10.3.19.0 255.255.255.0 10.2.19.2 R1#show ip route 查看路由表: ...
Theip policy route-mapinterface configuration command is used to define a route map used for PBR. In the example on the above slide, theip policy route-map PBRmapcommand applies the route map named “PBRmap” to the incoming traffic on the interface. Theip local policy rout...
•For PBR, route-map statements marked as deny are not supported.For more information about configuring route maps, see the "Using Route Maps to Redistribute Routing Information" section.You can use standard IP ACLs to specify match criteria for a source address or extended IP ACLs to specify...
the acl. So you need to rewrite your route map with a deny statement for DHCP traffic eg.route-map ACBPR deny 10 match ip address ACPBR_DHCP ip access-list extended ACPBR_DHCP permit udp any any eq bootps log 此方法在启用pbr后，可保证在相应的vlan中可获得ip address ...
(IPv6 access-list configuration) 2-418 permit (MAC access-list configuration) 2-424 police 2-427 police aggregate 2-429 policy-map 2-431 port-channel load-balance 2-434 power inline 2-436 power inline consumption 2-439 power inline police 2-441 power rps 2-444 power supply 2-446 ...