1)进入端口配置模式 2）配置VLAN Trunk模式：Switch(config-if)#switchport mode trunk 3)封装VLAN协议...
Switch1(config-if)#switchport access vlan 10//把端口fastEthernet 0/1加到vlan 10 Switch1(config)#interface fastEthernet 0/3 Switch1(config-if)#switchport access vlan 20//把端口fastEthernet 0/3加到vlan 20 Switch1(config-if)#exit Switch1(config)#interface fastEthernet 0/6 Switch1(config-if...
透過LAN介面(也就是連線LAN網路的介面)建立服務執行個體,以重疊特定VLAN (802.1q標籤流量) -在此案例中,為VLAN 1: ! interface FastEthernet0/1/7 no ip address negotiation auto cdp enable no shut ! 先刪除VLAN標籤,然後再透過重疊傳送流量,並在返回流量傳送到VLAN後推送此標籤: ! service instance 1 eth...
Cisco IOS 软件 Switch_IOS(config)#vlansecondary_vlan_idSwitch_IOS(config-vlan)#private-vlanisolatedSwitch_IOS(config-vlan)#nameisolated_pvlanSwitch_IOS(config-vlan)#exit 将一个或多个隔离 VLAN 绑定到主 VLAN。 CatOS Switch_CatOS> (enable)set pvlanprimary_vlan_id secondary_vlan_idVlan 101 conf...
Last Source Address:Vlan : 0060.70E5.CDD1:1 Security Violation Count : 0 3. Port Security Actions 1.Note that the shutdown option does not actually add the shutdown subcommand to the interface configuration. Instead, IOS puts the interface in an error disabled (err-disabled) state, which ma...
Because the router then has an interface connected to each VLAN, the router can also be configured with an IP address in the subnet that exists on each VLAN. Routers use subinterfaces as the means to have an interface connected to a VLAN. The router needs to have an IP address/mask ...
Interface System L State Hold (secs) SNPAfxp2.811111.1111.11111Up22 JUNOS逻辑路由器(Logical Routers)互联网接入 下一步,我们完成逻辑路由器到互联网的接入配置。由于当前JUNOS逻辑路由器R1通过vlan-tagging接口fxp1.81,与JUNOS主物理路由器的vlan-tagging接口fxp2.81,实现了IS-IS的互联。便可以通过在主物理路由器上...
Example: Subscribe to Interfaces The sub_vlan1.txt defines the parameters for the subscription for the openconfig-interfaces (oc-if) interfaces/interface Vlan1 data. Copy and paste the contents into the ~/gnmi_proto/sub_vlan1.txt file: subscribe: < prefix: <> subscription: < path: < origin...
VLAN assignment on a switch is configured on a per-interface basis. That is, each switch port interface is assigned individually into a Layer 2 VLAN. If you have more than one switch connected and you want the same VLANs to belong across all switches, then aTrunk Portmust be configured ...
我们通过使用PBR来实现基于VLAN的负载均衡,例如公司有600人,每100人划分一个VLAN,共6个VLAN。这样我们让前VLAN 1 2 3通过默认路由走电信链路,让VLAN 4 5 6通过PBR走联通链路。 PBR的失效:当PBR失效后,所有流量都会通过路由表进行转发。PBR通过ARP刷新来判断失效,如图1所求,当R1整台路由器失效或接口down后,SW...