I'm running Cisco 7200 lastest image (153-3.XB12) on GNS3 added Gigabit interfaces but when I try to acces a range the command is invalid R1(config)#interface range GigabitEthernet 1/0 - 2 the doc said it should
Remember this command selects all interfaces within a single slot, for example:Router(config-if)# interface range fastethernet 5/1 - 5 In this example, slot 5 has only 5 interfaces available.Now if you are looking to add more interfaces from a different slot, you can use the command ...
Range: 1 through 2147483647 kbps Command Default By default, bandwidth notifications are not generated. Command Modes SD-WAN physical interface configuration mode (config-interface-interface-name) Command History Release Modification Cisco IOS XE Catalyst SD-WAN Release ...
当您查看show interfacecard-type {slot/port} status命令时,Cisco IOS会执行以下操作: Router#show interface fastethernet 2/4 statusPort Name Status Vlan Duplex Speed Type Gi2/4err-disabled1 full 1000 1000BaseSX !--- The show interfaces card-type {slot/port} status command for Cisco IOS !---...
interface vlan +vlan号 进入VLAN接口模式(应用于三层交换) ip add +ip地址 为VLAN配置管理IP地址 vtp+service/tracsparent/client 配置SW的VTP工作模式 vtp +domain+域名 配置SW的VTP域名 vtp +password +密码 配置SW的密码 switchport mode trunk 启用中继 ...
Switch(config)# interface tengigabitethernet1/0/1 同时对多个接口进行配置 Switch(config)# interface range gigabitethernet1/0/1 - 3 , tengigabitethernet1/0/1 - 2 Edit 系统监控 1. 配置日志服务器 (config)#logging 192.168.1.30 2. SNMP设置 ...
interfaceconfigurecommand:(界面配置命令) access-expressionBuildabridgebooleanaccessexpression arp(地址协议)Setarptype(arpa,probe,snap)ortimeout backupModifybackupparameters bandwidthSetbandwidthinformationalparameter bridge-groupTransparentbridginginterfaceparameters carrier-delaySpecifydelayforinterfacetransitions cdpCDP...
interface 选择要配置的接口 Ethernet IEEE 802.3 FastEthernet IEEE 802.3快速以太网 0/1==槽位/该槽位下的端口 GigabitEthernet GigabitEthernet IEEE 802.3z Port-channel 接口以太网通道 Vlan Catalyst Vlans range 接口范围命令 ip 全局IP配置的子命令 ...
router(config)#privilegemodelevellevelcommand84.设定用户特权级:router(config)#enablesecretlevel3dallasrouter(config)#enablesecretsan-franrouter(config)#usernamestudentpasswordcisco85.标志设置与显示:R1(config)#bannermotd'unauthorizedaccesswillbeprosecuted!'86.设置vty访问:...
[Switch-Vlan-interface3] quit # 将端口GE1/0/2加入到指定VLAN。 [Switch] interface GigabitEthernet 1/0/2 [Switch-GigabitEthernet1/0/2] port switchcess vlan 3 [Switch-GigabitEthernet1/0/2] quit # 开启全局802.1x认证。 [Switch] dot1x # 配置802.1x认证的认证方法为CHAP。 [Switch] dot1x ...