1、控制面板-〉文件夹选项-〉查看-〉简单的文件共享， 取消掉 ；2、文件所在的目录-〉右键，属性-〉安全-〉高级-〉继承父目录权限， 取消掉。试下看行不行或者：1、找到该文件或文件夹－右击－属性－安全－在“允许”下选择完全控制－应用。如果这样不行的话就用下面的办法。2、找到该文件－右击...
cisco 3650 灾难恢复模式(switch:),flash为read-only只读.无法新建或者copy文件到flash 可以通过外插u盘...
Before it was possible to use the flash in read-write mode, now it's not possible, the question is it possible to change it or not, also, where is this change mentioned in the documentation. If you don't know any answer to these questions - why are you arguing? :) 0 Helpful Rep...
Does anyone know how to recovery from this 1130 AP. The flash is deleted. I tried to search the recovery steps but there is no document on this. Thanks! ap: dir List of filesystems currently registered: flash[0]: (read-write) xmodem[1]: (read-only) null[2]: (read-write) tf...
(read-only test): Formatting bootflash: mke2fs 1.35 (28-Feb-2004) Checking for bad blocks (read-only test): Formatting SAM partition: mke2fs 1.35 (28-Feb-2004) Checking for bad blocks (read-only test): Formatting Workspace partition: mke2fs 1.35 (28-Feb-2004) Checking for bad blocks...
%$ VDC-1 %$ %KERN-2-SYSTEM_MSG: [ 1677.470411] EXT4-fs (sda3): Remounting filesystem read-only - kernel Further, the logs also indicate a bootflash diagnostic test failure. %$ VDC-1 %$ %DIAGCLIENT-2-EEM_ACTION_HM_SHUTDOWN: Test <BootFlash> has been disabled as a part of defaul...
flashcisco交换机xmodemflashfs恢复方法 一台cisco3500不小心删除了FLASH文件,不能正常BOOT,急,没地方有启动文件下载,也联系不上cisco,正急时,我发现网络中还有台cisco3550,于是通过TFTP,进入/FLASH目录中,把其中的三个重要启动文件,备份下来,然后打开已不行的那台交换机,等到SWITCH提示后,采用XMDOEM方法传送文件到FLAS...
hwpart Read HW resources partition rommon 2 > dev //查看设备表 Devices in device table: id name flash0: compact flash 0 flash: compact flash 0 flash1: compact flash 1 bootflash: boot flash usbflash0: usbflash0 usbflash1: usbflash1 ...
在Cisco路由器上执行一条命令后得到下列信息 File Length Name/status 1 3638796 igs-d-1.102-2 [3638860 bytes used,555444 available,4194304 total] 4096K bytes of processor board System flash(Read ONLY) 那么该路由器执行的命令是 A. Router#show configuration B. Router#show flash C. Router>show ip...
Configure read-only SNMP community string (yes/no) [n]: //配置只读SNMP共同体字符串 Configure read-write SNMP community string (yes/no) [n]: //配置读写SNMP共同体字符串 Enter the switch name : MDS9148-1 //配置交换机名称 Continue with Out-of-band (mgmt0) management configuration? (yes/...