1.端口启用Port Security interface e0/0 switchport port-security 2.查看端口的Port Security配置 Switch#show port-security interface ethernet 0/0 Port Security : Enabled Port Status : Secure-up Violation Mode : Shutdown Aging Time : 0 mins Aging Type : Absolute SecureStatic Address Aging : Disable...
2,交换机设置 enable 进入特权模式 configure terminal 进入全局配置模式 interface f0/1 进入f0/1端口 no shutdown 激活端口 switchport mode access 把端口改为访问模式 switchport port-security 打开端口安全模式 switchport port-security maximum 1 设置该端口的的mac条目最大为1,即只允许一个设备接入 switchport ...
--- or you can manually re-enable it by entering the !--- shutdown and no shutdown interface configuration commands. Cat3750#show port-security interface fastEthernet 1/0/2 Port Security : Enabled Port Status : Secure-shutdown Violation Mode : Shutdown Aging Time : 0 mins Aging...
switchport port-security [violation {protect | restrict | shutdown}] 参数说明 switchport port-security violation shutdown //违规后执行动作shutdown(err-disable),默认执行策略就是把端口err-disable掉 switchport port-security violation protect//将违规的mac地址的流量丢弃,不记录 switchport port-security viola...
switch(config-if)#switchport port-security maximum number /默认每个接口最大的值为1 switch(config-if)#switchport port-security violation protect|restrict|shutdown /启用安全违规行为 protect:当接口学习到设定数量的MAC后,后来的MAC信息将直接丢弃,且不产生通知 restrict: 当接口学习到设定数量的MAC后,后来的MA...
本文介绍您在Cisco Business 220系列交换机上的端口安全选项。 适用设备 |固件版本 CBS220系列(产品手册) |2.0.0.17 简介 通过限制对具有特定MAC地址的用户的端口访问,可以提高网络安全性。MAC地址可以动态获取,也可以静态配置。端口安全监控已接收和已获取的数据包。对锁定端口的访问仅限于具有特定MAC地址的用户。
(欺骗)攻击预防方法:有效配置交换机port-securitySTP攻击预防方法:有效配置rootguard,bpduguard,bpdufilterVLAN,DTP攻击预防方法:设置专用的nativevlan;不要的接口shut或将端口模式改为accessDHCP攻击预防方法:设置dhcpsnoopingARP攻击预防方法:在启用dhcpsnooping功能下配置DAI和portsecurity在级联上层交换机的trunk下switch(...
https://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/admin_management.html#pgfId-1711061找到这个官方连接,看到连接以下步骤的说明:第一说明密码过期有个问题 Command Purpose Step 1 password-policy lifetime days ciscoasa(config)# ...
3.BPDUportguard 4.UDLD 5.Link-flaperror 6.Loopbackerror 7.Portsecurityviolation 第一个当FEC两端配置不匹配的时候就会出现err-disable。 假设SwitchA把FEC模式配置为on,这时SwitchA是不会发送PAgP包和相连的SwitchB去协商FEC的,它假设Switch B已经配置好FEC了。但实事上Swtich B并没有配置FEC,当Switch B的这...
enable password[password] 配置接口、路由 interfaceinterface_name nameif[name] name 有三种接口类型 insdie outside dmz security-levelxx(数值) 数值越大接口安全级别越高 注:默认inside 100 ,outside 0 ,dmz 介于二者之间 静态路由 routeinterface_number network mask next-hop-address ...