Router#configure terminal 输入配置命令,每行一个。以 CNTL/Z 结尾。 Router(config)# 3、通过使用 IP DHCP 排除地址FIRST_IP LAST_IP路由器(配置)排除 IP 地址 #ip Router(config)#ip dhcp excluded-address 192.168.0.1 192.168.0.50 Router(config)# 4、使用 ip dhcp pool NAME 命令 Router(config)#ip ...
步驟15.按一下Configure Devices,等待任務完成。 通過CLI在Cisco IOS XE SD-WAN路由器上配置DHCP伺服器 步驟1.導覽至組態模式。 cEdge#config-transaction admin connected from 127.0.0.1 using console on Router cEdge(config)# 步驟2.配置DHCP池,分配此處列出的值,並儲存更改。 名稱:為DHCP池命名...
Step 1. Enable DHCP server/ configure the DHCP Pool. Step 2. Configure the advanced parameters. Step 3. Configure the DNS/ WINS Server. Note: Ensure that the IP address and logical name must be configured on the interfaces before you start DHCP configuration. ...
1、创建DHCP池:使用ip dhcp pool命令创建一个DHCP池,并为其指定一个名称,创建一个名为“Floor1DHCP”的DHCP池。 Router(config)#ip dhcp pool Floor1DHCP 四、配置DHCP池参数 1、定义子网:使用network命令指定DHCP分配地址的网段和子网掩码,为192.168.0.0/24网段分配IP地址。 Router(dhcp-config)#network 192.168...
在本文中,将学习如何使用 CLI 将思科路由器配置为 DHCP 服务器,以及如何使用 configlet 在 NCM 应用程序中同时在多个设备上更新它。 通过CLI 配置 DHCP 服务器的步骤 1、使用SSH / TELNET登录到设备并转到启用模式。 2、进入配置模式。 Router#configure terminal ...
在Cisco路由器上配置DHCP服务器的步骤如下: 1、登录并进入配置模式:通过SSH或TELNET登录到设备,并进入启用模式,然后输入configure terminal进入配置模式。 2、排除IP地址:使用ip dhcp excluded-address命令排除不需要分配的IP地址范围,排除192.168.0.1到192.168.0.50的地址: ...
R1(config-if)#ip helper-address13.1.1.3//网关接口设置中继,实现将用户网段内的DHCP请求中继到服务器网段的DHCP服务器获取地址 R3配置信息(DHCP Server): Router>enable Router#configure terminal Router(config)#hostname Server Server(config)#interfaceethernet0/0Server(config-if)#ip address13.1.1.3255.255.255...
ITKE-AP01#configure terminal ITKE-AP01(config)#ip dhcp excluded-address 172.16.0.1 – 172.16.0.50 ITKE-AP01(config)#ip dhcp pool ITKE ITKE-AP01(dhcp-config)# network 172.16.0.0 255.255.255.0 ITKE-AP01(dhcp-config)#lease 20 ITKE-AP01(dhcp-config)#default-router 172.16.0.1 ...
R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. ###开启dhcp server 功能 R1(config)#service dhcp R1(config)#ip dhcp pool R123 R1(dhcp-config)#network 123.1.1.0 255.255.255.0 ###将客户端的网关指向 dhcp server 接口的IP R1(dhcp-config)#default-router...
This example uses a Cisco switch as the DHCP server to describe how to configure Option 43 to carry the WAC's IP address of 192.168.100.1. # ip dhcp pool test network 192.168.100.1 255.255.255.0 default-router 192.168.100.1 option 43 hex 030d3139322e3136382e3130302e31 # 03: suboption ...