interface fastethernet0/1 进入要配置的端口 spanning-tree vlan 8 port-priority 10 将端口权值10赋与VLAN 8. spanning-tree vlan 9 port-priority 10将端口权值10赋与VLAN 9. spanning-tree vlan 10 port-priority 10将端口权值10赋与VLAN 10. interface fastethernet0/2 进入F0/2 spanning-tree vlan 3 po...
*Mar 1 00:26:10.719: OSPF: Send hello to 224.0.0.5 area 0 on Serial1/2 from 123.1.1.1 *Mar 1 00:26:15.627: OSPF: Rcv hello from 22.22.22.22 area 0 from Serial1/2 123.1.1.2 *Mar 1 00:26:15.631: OSPF: Send immediate hello to nbr 22.22.22.22, src address 123.1.1.2, on Serial...
interface fastethernet0/1 进入要配置的端口 spanning-tree vlan 8 port-priority 10 将端口权值10赋与VLAN 8. spanning-tree vlan 9 port-priority 10 将端口权值10赋与VLAN 9. spanning-tree vlan 10 port-priority 10 将端口权值10赋与VLAN 10. interface fastethernet0/2 进入F0/2 spanning-tree vlan 3...
但是,由于单播 OSPF 数据包从两台交换机的 Ethernet1/1 传出并被 N9K-2 和 N9K-4 丢弃(如本文档的“带有 vPC对等网关的背靠背 vPC 上的单播路由协议邻接”部分所述),N9K-1 和 N9K-4 之间的 OSPF 邻接卡在“EXSTART“或“EXCHANGE”状态。同样,由于单播 OSPF 数据包从两台交换机的 Ethernet1/2 传出并...
使用show ospf interface 命令進行驗證。 asa(config)# show ospf interfaceinside is up, line protocol is up Internet Address 198.51.100.1 mask 255.255.255.0, Area 0 Process ID 928, Router ID 198.51.100.1, Network Type BROADCAST, Cost: 10 Transmit Delay is 1 sec, State DR, Priority 1 Designate...
51、izon;水平分隔QuidwayrouteridA.B.C.D;配置路由器的IDQuidwayospfenable;启动OSPF协议Quidway-ospfimport-routedirect;引入直联路由Quidway-Serial0ospfenablearea;配置OSPF区域华为路由器交换机配置命令:标准访问列表命令格式如下:aclmatch-orderconfig|auto;默认前者顺序匹配。rulenormal|specialpermit|denysourcesource-...
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route ...
Why does router ID 10.255.255.12 chooses intra-area link even with maximum ip ospf cost in the folowing schema (for better resolution pls. see the attached one): What is the workaround? Tunnel between RID 48 and RID 11 is not acceptable. Thanks! I have this problem too Labels: Routing...
Config/networkProcessor/com/metasolv/serviceactivator/cartridges/cisco/pre_check/standard.properties.txt To disable a particular pre-check or post-check, change its value tofalse, as shown in the example below. The valuetrueindicates an enabled pre-check or post-check. ...
router ospf 1 area 0 interface Bundle-Ether100 priority 255 ! interface Bundle-Ether200 priority 255 ! interface Loopback0 ! ! ! router bgp 65001 bgp router-id 10.10.1.1 address-family ipv4 unicast ! address-family l2vpn vpls-vpws ! neighbor 10.10.1.2 remote-as 65001 description *** PE1 ...