8口E1专线模块 NIM-8CE1T1-PRI 专线模块NIM-1GE-CU-SFP光电复用 专线模块NIM-2GE-CU-SFP光电复用 NIM-1MFT-T1/E1(1口E1专线模块) NIM-2MFT-T1/E1(2口E1专线模块) NIM-4MFT-T1/E1(4口E1专线模块) NIM-8MFT-T1/E1(8口E1专线模块) 语音模块NIM-2T (2串口专线接口) ...
Cisco WAN Network Interface Module NIM-2T 2-Port Serial WAN Interface Card, Find Details and Price about NIM-2T switch moudle from Cisco WAN Network Interface Module NIM-2T 2-Port Serial WAN Interface Card - HELPYOU GROUP CO., LTD.
Cisco Nexus交换机的48端口n2k-c2248tp-e 查看详细信息 全新原装思科Nexus 480 Gbps n3k-c3524p-1... 查看详细信息 伊斯科n5548子卡模块n55-d160l3-v2 = 查看详细信息 更多来自该供应商的产品 全新原装思科vwic3-1mft-t1 / E1端口模块 查看详细信息 全新原装glc-lh-smd 1000base思科SFP模块 查看详细信...
思科WS-C2960X/XR-24/48TS/PS/TD/LPD/FPS/FPD-L/LL/I 千兆交换机 型号:WS-C3080X-24TS-LL 0+条评论 思科(CISCO)NIM-1T/2T/4T/4FXS/4FXO适用于ISR4000路由器广域网模块 型号:NIM-1T= 0+条评论 思科(CISCO)NIM-1T/2T/4T/4FXS/4FXO适用于ISR4000路由器广域网模块 型号:NIM-4T= ...
C1000(1) C8200L(1) Previous Next Forum Posts Sorted by: Start a conversation Migrate RIP to OSPF Hi Everyone,I am currently doing research to setup up OSPF while migrating from RIP V2. From what I understand I can have both protocols running at the same time - I would just need to...
NIM-8CE1T1-PRI3.13 / 17.3 / 19.13.13 / 17.3 / 18.43.13 / 17.3 / 18.3No8 port Multi-flex Trunk Voice/Channelized Data T1/E1 Module Storage 4461445144314351433143214221 Minimum IOS XE / XE SD-WAN / vManage NIM-SSD3.10 /No /NoNoNIM Carrier Card for up to 2 SSD Drives ...
NIM-1T/2T/4T/2FXS/4FXOP/2FXO/4FXO/4E/M/16A/24A/ES2-4/8-P模块 Cisco/思科 品牌 一件代发 ¥9500.0 余姚科曼通信设备厂 1年 缤特力(PLANTRONICS)SP11-RJ9(CISCO)单耳客服耳麦 CISCO话机专 缤特力(PLANTRONICS) 品牌 48小时发货 ¥219.0 北京明川欣业通讯科技有限公司 17年 明川欣业MRD...
请教ISR4331配NIM-2T模块的配置 本帖最后由 xy411381121 于 2019-5-23 20:24 编辑 地方上以前用的路由器是C1760、C2801、2801C、C2901这类老路由器,使用2M通道。以C2901路由器为例:有些C2901/K9路由器3槽位上装了块HWIC-2T,自动就识别到了Serial0/3/0与Serial0/3/1;有些C2901/K9路由器3...
NIM-ES2-4 4-port Layer 2 GE Switch Network Interface Module.$648.90$221.00 (66% OFF)Buy Now 9 WS-C3850-24XS-S Cisco Catalyst 3850 24 Port 10G Fiber Switch IP Base.$42,719.51$8,316.00 (81% OFF)Buy Now 10 WS-C3850-24XS-E
Step c. Configure Boot variables:(Currently there is no boot variable set, as this is the first time we are upgrading the devices after installation) conf tboot system flash bootflash:packages.confboot system flash bootflash:asr1001x-universalk9.16.09.02.SPA.binendwr Step d. Reboot the appli...