ASA(config)# show run global ASA(config)# show xlate ASA(config)# show connect 3.配置PAT 把内部网段: 转换成为一个外部的一个地址:配置命令 ASA(config)# nat (inside) 2 (定义源网段) ASA(config)# global (outside) 2 (定义地址) ASA(config)# global (outside) 2 interface(或者直接转换为外...
这些命令指示 ASA 将源地址转换为 209.165.201.3 到 209.165.201.29,以便前 27 个内部用户通过 ASA。这些地址用完后,ASA 会将所有后续源地址转换为 209.165.201.30,直到 NAT 池中有一个地址变为空闲状态。 注意:NAT 语句中使用了通配符编址方案。此语句告诉 ASA 在离开互联网时转换任何内部源地址。如果需要,此命...
There are two sets of syntax available for configuring address translation on a Cisco ASA. These two methods are referred to asAuto NATandManual NAT. The syntax for both makes use of a construct known as anobject. The configuration of objects involve the keywordsrealandmapped. In Part 1 of ...
Note: When you have an interface with a NAT policy and if there is no global pool to another interface, you need to use nat 0 in order to set up NAT exception. ASA Version 8.3 and Later Here is the configuration. object network obj-10.0.0.0/8 ...
ASA Pre-8.3 to 8.3 NAT configuration examples Magnus Mortensen Cisco Employee 05-12-2010 09:06 AM - edited 03-08-2019 06:32 PM Static NAT/PAT Pre-8.3 NAT8.3 NAT Regular Static NAT static (inside,outside) 192.168.100.100 10.1.1.6 netmask 255.255.255.255 object network obj-10....
ASASASA的NATATAT配置置置 1.nat-control.nat-control.nat-control命令解释令解释令解释pix7.0ix7.0ix7.0版本前默认为本前默认为本前默认为nat-control,at-control,at-control,并且不可以更改且不可以更改且不可以更改ix7.0ix7.0ix7.0版本后默认为本后默认为本后默认为nooonat-controlat-controlat-control。可以类似...
Sample ASA configuration for connecting to Azure VPN gateway ! ! Tested hardware: ASA 5505 ! Tested version: ASA version 9.2(4) ! ! Replace the following place holders with your actual values: ! - Interface names - default are "outside" and "inside" ! - <Azure_Gateway_Public_IP> ! -...
NAT很简单: 1.对应内外网:IP。 2.开启对应的端口NAT功能 3.对应内外网:服务 IP+port 静态配置:local-ip对应global-ip (1) 在local-ip和global-ip之间建立静态地址转换 Router(config)#ip nat inside source s
在ASA防火墙配置NAT分为4种类型:动态NAT、动态PAT、静态NAT、静态PAT。 结合实验拓补来了解如何配置这四种NAT类型: 基本配置已经配置完成 动态PAT转换配置方法: ASA(config)# nat (×××ide) 1 10.1.1.0 255.255.255.0 #声明内部地址,nat-id为1 ASA(config)# global (outside) 1 30.1.1.100-30.1.1.200 ...
ASA5516,版本:Version 9.8(2) ASA防火墙做为出口,只有一个公网地址做了PAT。 在做内网服务器端口映射的时候,提示如下: PVSZ-FW(config-network-object)# nat (inside,outside) static isp service tcp 80 80 ERROR: Address 202.100.100.6 overlaps with outside inter