Can u pls explain in detail about the below commands which I found for 2960 switch model, its significance? line con 0exec-timeout 2 40line vty 0 4session-timeout 3exec-timeout 0 0transport preferred nonetransport input sshtransport output sshline vty 5 15session-timeout 3exec-timeout 0...
Cisco 2960 交换机密码设置 1、设置全局密码 Switch>en Switch#conf t Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#enable password contoso Switch(config)#end 2、设置console密码 Switch>en Switch#conf t Enter configuration commands, one per line. End with CNTL/Z. S...
30FLoor-2960-1(config)#ip default-gateway网关ip 例如:30FLoor-2960-1(config)#ip default-gateway 10.11.90.254 4)设置路由 30FLoor-2960-1(config)#ip route0.0.0.0 X.X.X.X 5)设置console口密码 30FLoor-2960-1(config)#line console 0
Switch(config)#hostname 配置的交换机姓名 如：30FLoor-2960-1 30FLoor-2960-1(config)#end 30FLoor-2960-1# 2）配置交换机的ip 30FLoor-2960-1#configure terminal (进入配置状态)30FLoor-2960-1(config)#interface vlan 1 30FLoor-2960-1(config)#ip address ip地址 子网掩码 例如：30FLoor-2960-1(...
Catalyst 2960 Switch Cisco IOS Commands - rmon collection through show vtp Catalyst 2960 Switch Cisco IOS Commands - shutdown through vtp Catalyst 2960 Switch Bootloader Commands Catalyst 2960 Switch Debug Commands Catalyst 2960 Switch Show Platform Commands Acknowledgments for Open-...
2)建立实验网络拓扑在Packet Tracer程序主窗口中,添加一台Cisco 2960交换机、一台普通PC机,并添加Console连接、直通网线连接,如图-13所示,确认完毕后将当前拓扑结构保存为c2960-pc.pkt文件。 图-13 其中,连接细节如下: 交换机的Console口 <--> PC机的RS 232串口。
1、cisco 2960 交换机安装配置基础新设备配置内容:1. interface vlan 1 的 ip,gatewayconf tintvlan 1ip address xx.xx.xx.xx ip default-gateway ip-addressno shutdownexit2. en 的密码3.line vty 0-4 telnet 的密码4.wr 存盘show interface vlan 1show run将 F0/1-10 端口加入到 VLAN20 中 ,对应...
90.2544)设置路由30floor2960-1(config)ip route 0。0.0.0 x.x.x.x5)设置console口密码30floor2960-1(config)line console 030floor29601(config-line)#password 输入密码30floor-2960-1(config-line 5、)#login30floor-29601(config-line)end6)设置telnet的密码30floor2960-1(config)#line vty 0 1030floor...
2960交换机远程就是dhcp中无法显示IP 地址及mac,全局配置也做了ip dhcp snooping,端口聚合也配了 ip dhcp snooping trust,端口是状态是正常的,端口接的电脑也正常获取IP地址,配置如下,请各位大佬帮帮我。#sho runBuilding configuration...Current configuration : 12640 bytes!! Last configurati...
properly pre-configured to provide required multicast filtering and quality of service (QoS) features. This document explains the required steps to configure Cisco 2960 switch specifically. These commands may be applicable to other members of the Catalyst product line that support these same commands....