monitor session 1 destination interface 我 做下补充吧 第一个是 要抓数据出来看的接口---连接PC或者网络分析仪器 第二个是 你数据正常在这接口走出去 连接上层设备啥的
Switch# clear interface fastethernet0/5 关闭和打开端口 命令 目的 Step 1 configure terminal 进入配置状态 Step 2 interface {vlan vlan-id} | {{fastethernet | gigabitethernet} interface-id} | {port-channel port-channel-number} 选择要关闭的端口 Step 3 shutdown 关闭 Step 4 end 退出 Step 5 show...
Switch#clear interface fastethernet0/5 3.3.3 命令 目的 Step 1 configure terminal 进入配置状态 Step 2 interface{vlanvlan-id} | {{fastethernet|gigabitethernet}interface-id} | {port-channelport-channel-number} 选择要关闭的端口 Step 3 shutdown 关闭 Step 4 end 退出 Step 5 show running-config 验...
Cisco SRW2024 24-Port Gigabit Switch: WebView Cisco Small Business Managed Switches Highly Secure, Reliable, Intelligent Switching for Your Growing Businesses Highlights ● 24 high-speed ports optimized for the network core or to support bandwidth-intensive applications ...
Figure 1. Cisco SLM2024 24-Port Gigabit Smart Switch with 2 SFPs Product Overview Cisco ® Small Business Smart Switches are cost-effective switching solutions that are ideal for small businesses, the network edge, or workgroups within larger organizations. These easy-to-install, high-speed ...
Switch# configure terminal Switch(config)# interface range fastethernet0/1 - 5 Switch(config-if-range)# no shutdown Switch(config-if-range)# *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/...
port-channel-number, port-channel 号从 I 到64 端口号之间需要加入空格,如:interface range fastethernet 0/1 - 5是有效的,而 interface range fastethernet 0/1-5 是无效的. interface range命令只能配置已经存在的interface vlan 所有在同一组的端口必须是相同类别的。见以下例子: Switch# configure terminal ...
但对亍GBIC 端口则不能配置速率及双工模式,有时可以配置nonegotiate,当需要联接不支持自适应的其它千兆端口时 Switch# configure terminal Switch(config)# interface fastethernet0/3 Switch(config-if)# speed 10 Switch(config-if)# duplex half 端口描述 “思科cisco2950 交换机配置手册(中文)2”文档源亍网络,本...
192.168.1.100255.255.255.0(VLAN1里面设置IP地址)2950(config)#ipdefault-gateway192.168.1.1(设置默认网关)2950(config)#ipname-server192.168.1.1(设置域名服务器)2950(config)#ipdomain-namewqs(设置域名)端口配置2950(config)#intf0/1(进入接口)2950(config-if)#speed100(设置该接口速率为100Mb/s)2950(config...
Switch(config-if-range)#no shutdown Switch(config-if-range)# *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEth...