(Cisco Controller) >config ap unifiedmode <switch_name> <switch_ip_address> <switch_name> and <switch_ip_address> is the name and IP address respectively of the WLC to which the APs need to be migrate. Note The above command converts all connected Access Point...
Switch(config)# Interface fastethernet 0/1 ＃进入具体端口配置模式 Switch(config-if)#Switchport port-secruity ＃配置端口安全模式 Switch(config-if )switchport port-security mac-address MAC(主机的MAC地址)＃配置该端口要绑定的主机的MAC地址 Switch(config-if )no switchport port-security mac-a...
Use this command to create a DHCP pool of IP addresses to be used by the Switched Virtual Interface (SVI) (Refer Step 11 and further for SVI). Step 3 default-routerip address Example: Router(dhcp-config)#default-router 10.10.10.1
SW1(config)#ip default-gateway 192.168.1.254 #设置该交换机的默认网关 SW1(config)#int vlan1 #进入vlan1的端口 SW1(config-if)#ip address 192.168.1.1 255.255.255.0 #配置交换机的管理地址为192.168.1.1子网掩码为255.255.255.0 SW1(config-if)#no shutdown #启动这个vlan1 3、配置R1路由器 Router(co...
步骤6default-routerip_address为池指定DHCP默认路由器的IP地址。 注我们建议DHCP的默认路由器地址位于VLAN1 上。新安装的设备将在VLAN1上搜索DHCP和 TFTP。 步骤7file-serveraddress指定TFTP服务器的IP地址。 注如果指挥交换机也是TFTP服务器,则必须启用它。 请参阅第2-7页上的“配置TFTP服务器”一节。 步骤8exi...
幌刻蔷喉哨寻芒努挣焊漂凳妒缉绎四腆悼墩契与哲困颊勺辈米乾均画安侦CISCO无线控制器配置基础思科中小企业统一通讯方案部署和功能演示系统启动界面(续)非常重要,Controller的wirel配置3层交换机pdhcpexcluded-addressipdhcpexcluded-address54ipdhcpexcluded-address!ipdhcppoolAPnetworkdefault-router54!interfaceFast...
receiver ip address 10.1.1.3 57500 protocol grpc-tcp (receivers IP, port and protocol) This telemetry configuration has already been applied to the switch. However, if it needs to be re-applied the following can be used to easily copy/paste: ...
Switch> (enable)sh port status 3/1Port Name Status Vlan Duplex Speed Type --- --- --- --- --- --- --- 3/1disabled1 auto auto 10/100BaseTX!--- Theshow port status {mod/port}command show the port is disabled. !--- Use theset port enable {mod/port}command to try and ...
Cisco Layer 3 switch enables IP routing 一、网络拓扑 二、三层交换机配置内容 #vlan11//创建 VLAN 11#exit #vlan12//创建 VLAN 12#exit #vlan13//创建 VLAN 13#exit #ip routing//启用IP路由#interface Vlan 11//创建 VLAN 11 的虚拟接口#ip address192.168.11.1255.255.255.0//配置虚拟接口 VLAN 11 ...
Note:Select theEnable NAT Addresscheck box and enter the external NAT IP address if you want to be able to deploy your Cisco 5500 Series Controller behind a router or other gateway device that is using one-to-one mapping network address translation (NAT). NAT allows a device, such as a ...