但实事上Swtich B并没有配置FEC，当Switch B的这个状态超过1分钟后，Switch A的STP就认为有环路出现，因此也就出现了err-disable。解决办法就是把FEC的模式配置为channel-group 1 mode desirable non-silent这个意思是只有当双方的FEC协商成功后才建立channel，否则接口还处于正常状态。
9/9 channel-misconfig Enable Enabled 9/10 channel-misconfig Enable Enabled 9/11 channel-misconfig Enable Enabled 9/12 channel-misconfig Enable Enabled I have this problem too Labels: Other Switching 0 Helpful Reply All forum topics Previous Topic Next Topic 2 Accepted Solutions Thotsaphon Lu...
set port channel 6/5-8 915 set port channel 6/9-12 916 set port channel 6/13-16 917 set port channel 6/28 920 set port channel 6/29-31 921 set port channel 6/37-39 923 set port channel 6/45-48 925 set port channel 6/21-24 948 set port channel 7/1-4 979 set port chann...
“spanning-tree etherchannel guard misconfig”详解 1. 含义 spanning-tree etherchannel guard misconfig 是一个用于Cisco交换机上的STP(生成树协议)配置命令,旨在增强网络稳定性。当在Cisco交换机上启用此功能时,它会监控EtherChannel链路上的STP配置。如果检测到STP配置不一致(即EtherChannel中的某些端口与其他端口在...
channel-group 1 mode on after that, 3750X stack show me a error-disable message: *Mar 1 00:04:00.266: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Gi1/0/24, putting Gi1/0/24 in err-disable state *Mar 1 00:04:00.333: %PM-4-ERR_DISABLE: channel-misconfig (STP)...
9/9 channel-misconfig enable enabled 9/10 channel-misconfig enable enabled 9/11 channel-misconfig enable enabled 9/12 channel-misconfig enable enabled solved! go to solution. i have this problem too labels: labels: other switching 0 helpful reply 37 replies 37 hi toshi. i am back. i guess...
channel-misconfig error detected on Po1, putting Te1/1/1 in err-disable state Jul 17 19:47:58.271: %PM-4-ERR_DISABLE: channel-misconfig error detected on Po1, putting Te1/1/2 in err-disable state Jul 17 19:47:58.279: %PM-4-ERR_DISABLE: channel-misconfig error detected on Po1, ...
.Jan 19 04:14:58.709: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Gi1/0/44, putting Gi1/0/44 in err-disable state.Jan 19 04:14:58.726: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Gi1/0/43, putting Gi1/0/43 in err-disable state.Jan 19 04:...
channel-misconfig Go to solution Rosa Ladeira Level 1 06-29-2011 12:57 PM - edited 03-07-2019 01:01 AM Hello. I am working on migrating from cat6509 to cat6509-E. I am trying to configure a TP ethernetchannel/trunk in order to change cats on the fly. I have 2 trunks...
channel-misconfig Go to solution Rosa Ladeira Level 1 06-29-2011 12:57 PM - edited 03-07-2019 01:01 AM Hello. I am working on migrating from cat6509 to cat6509-E. I am trying to configure a TP ethernetchannel/trunk in order to change cats on the fly. I have 2 trunks...