* @dist_avg: average of distances (mm) measured * (must have either this or @rtt_avg) * @dist_variance: variance of distances measured (see also @rtt_variance) * @dist_spread: spread of distances measured (see
M106 S{ (params.PERCENT | float) * 255 / 100 } [gcode_macro _RUNOUT_INFO] gcode = {% if 'filament_switch_sensor lgx' in printer.configfile.settings %} {% set enable = printer['filament_switch_sensor lgx'].enabled %} {% set detect = printer['filament_switch_sensor lgx']...
[airootfs.fs]/usr/share/doc/mkinitcpio-archiso/README.bootparams if [ -f /$esp/archlinux.iso ] ; then menuentry 'Arch Linux LiveCD [root/空]' --unrestricted { loopback loop0 /$esp/archlinux.iso linux (loop0)/arch/boot/x86_64/vmlinuz-linux archisobasedir=arch img_label=$esp img_...
We read every piece of feedback, and take your input very seriously. Include my email address so I can be contacted Cancel Submit feedback Saved searches Use saved searches to filter your results more quickly Cancel Create saved search Sign in Sign up Reseting focus {...
PE10 enable_pin: !PE9 rotation_distance: 40 microsteps: 16 endstop_pin: ^sht36v2:PA2 position_endstop: 0 position_max: 225 position_min: 0 homing_speed: 100 # Increase after initial setup, Max 100 homing_retract_dist: 5 homing_positive_dir: false step_pulse_duration: 0.000004 [tmc...
文件 main main update-readme-with-isaacsim-automator-info 克隆/下载 HTTPSSSHSVNSVN+SSH 该操作需登录 Gitee 帐号,请先登录后再操作。 提示 下载代码请复制以下命令到终端执行 为确保你提交的代码身份被 Gitee 正确识别,请执行以下命令完成配置 使用HTTPS 协议时,命令行会出现如下账号密码验证步骤。基于安全考虑...
PE9 rotation_distance:40microsteps:16endstop_pin:^sht36v2:PA2 position_endstop:0position_max:225position_min:0homing_speed:100# Increase after initial setup, Max 100homing_retract_dist:5homing_positive_dir:false step_pulse_duration:0.000004[tmc2209 stepper_x]uart_pin:PE7 interpolate:true run...
homing_retract_dist: 3.0 [tmc2209 stepper_z] uart_pin: PB3 uart_address: 2 interpolate: False # For FYSETC 42HSC1404B-200N8 run_current: 0.3 # This may need tuning depending upon the motors you are using sense_resistor: 0.220 stealthchop_threshold: 0 # Set to 999999 to turn stealthchop...
{% set e = params.E|default(1) %} #edit to your retract length G91 G1 E{e} F2100 G90 RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 BASE_RESUME [gcode_macro G32] #Gantry levelling macro gcode: BED_MESH_CLEAR G28 QUAD_GANTRY_LEVEL G28 G0 X150 Y150 Z30 F3600 [gcode_macro ...
Search or jump to... Search code, repositories, users, issues, pull requests... Provide feedback We read every piece of feedback, and take your input very seriously. Include my email address so I can be contacted Cancel Submit feedback Saved searches Use saved searches to filter your...