DM6467T开发板在CCS中Load Program失败 先描述下现象: 1. 开发板是我们打的,之前用的是DM6467(729 MHz)芯片,能做4路H264编码,后面想提高板子性能,换成DM6467T(1G Hz)的芯片。 板子重新焊接后,开发板外围硬件也做了些修改: (1). 修改核心芯片晶振,将原来27M晶振(6467)换成33.330M晶振(6467T) (2). ...
我们在拿自己做的TDA3x板子用CCS(10) Load Program时一直报如下错误(参考VisionSDK_UserGuide_TDA3xx.pdf),CCS Console里信息如下,错误信息:Cortex_M4_IPU1_C0: File Loader: Verification failed: Values at address 0x83500128 do not match Please verify target memory and memory map. 参照Data Verifica...
如果上述正常，检查调用的GEL文件中是否将这段内存正确添加入了memory map 工程里面有没有.ccxml文件 ，VIEW-Target configuration 看看 必须要LINK哦 菜鸟提示 我也是刚入手这个
NAND Boot failed. Starting UART BOOTPSP" 想不明白,同样一个UBL, UBOOT为什么最开始能够正常启动,后面就不行了呢?于是准备重新烧写UBL,UBOOT,更加严重的问题随之而来: 在CCS下加载nand_flash_writer.out到内存时,失败,如下图: 0 2018-5-31 04:44:03 评论 淘帖 邀请回答 李牧喜 相关推荐 • 请问...
After loading to the memory the debuger shows the error message: Load Program Failed: DWARF information is corrupted. Afterwards I see disassembly only and not C code (seems logical when there is a problem with loading of DWARF). We are using CodeSourceryG++Lit...
Power Failure on Target CPU Failed to remove the debug state from the target before disconnecting. There may still be breakpoint opcodes embedded in program memory. It is recommended that you reset the emulator before you connect and reload your program before you continue debugging. DSP设置段点...
C28xx: GEL: File: E:\dsp\zx_dsp2000\zx_project_c2000\Debug\zx_project_c2000.out: Load failed. 为吸取经验教训,总结了Flash锁死的可能原因,以后注意这些方面: (1)由于PC的原因,这里就是这样,中途打断了Flash的烧写过程造成Flash锁死。仿真器在烧写时挂起也会造成Flash锁死,比如有些仿真器速度比较慢,很...
Power Failure on Target CPU Failed to remove the debug state from the target before disconnecting. There may still be breakpoint opcodes embedded in program memory. It is recommended that you reset the emulator before you connect and reload your program before you continue debugging. DSP设置段点...
“Data verification failed at address 0x(某地址)Please verify target memory and memory map.” 按跳过提示下载完成后messages栏提示: Can't Set Breakpoint: Error 0x00000008/-1076 Error during: Break Point, Cannot set/verify breakpoint at 0x80007958 ...
2. But load program failed. Here's the information while clicking on test mode: [Start] Execute the command: %ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -F inform,logfile=yes -S pathlength -S integrity [Result]