然后将“code_start”替换成“_c_int00”,或者放置空白(前提是你的程序中已经有定义)就可以消除此WAINING。
【笔记】CCS4 出现 warning: entry-point symbol other than "_c_int00" specified: "code_start" 的解决方法 日记被设为不允许回应 赞 转发 > 我来回应 ×
;// The codestart section in the linker cmd file is used to physically place ;// this code at the correct memory location. This section should be placed ;// at the location the BOOT ROM will re-direct the code to. For example, ;// for boot to FLASH this code will be located at ...
两个 code_start 如下所示(即 DSP2833x_CodeStartBranch.asm)且看门狗已禁用。 code_start: .if WD_disable = 1 lb wd_disable 分支到看门狗禁用代码 .else LB _c_int00 ;分支到 RTS 库 .endif 中的 boot.asm 启动 ;结束 codestart 段 我在应用项目中添加了代码以...
【笔记】CCS4 出现 warning: entry-point symbol other than "_c_int00" specified: "code_start" 的解决方法 2010-02-28 15:45 −... OneSeven 0 15546 一些常见warning的原因和解决方法 2016-09-18 12:06 −在入职三周后,终于赶齐了接手项目落下两个月的项目,有了一些自己的空闲时间对项目进行整...
工具/软件:Code Composer Studio 您好, 构建一 个“旧”程序, 有警告: 警告#10063-D:未指定"_c_int00"的入口点符号: "code_start" 。 我不知道这是什么意思。 它是否会影响格拉姆跑步?
codestart : > BEGIN, PAGE = 0 ramfuncs : > RAML0, PAGE = 0 .text : > RAML1, PAGE = 0 .cinit : > RAML0, PAGE = 0 .pinit : > RAML0, PAGE = 0 .switch : > RAML0, PAGE = 0 .stack : > RAMM1, PAGE = 1 .ebss : > RAML4, PAGE = 1 ...
方式一:将文件DSP28_CodeStartBranch.asm(注意这个文件的代码在文章末位有)添加到工程中,之后在main.asm中添加如下语句即可,代码如下: .global _c_int00 _c_int00: NOP NOP ESTOP0 方式二:直接在main.asm中添加代码: code_start: NOP NOP ESTOP0 ...
烧写模式:在工程的 cmd 文件夹选择 F2833x_custom_flash.cmd 文件,且并在工程的 source 文件夹选中 DSP28xxx_CodeStartBranch.asm 和 DSP28xxx_SectionCopy_nonBIOS.asm 文件; 例如,如何完成F2833x_custom_ram.cmd选择文件和取消选择文件的切换。 图2:FLASH模式取消RAM.CMD文件 ...
CCS/LAUNCHXL-F28377S: Why Warning: Type #10063-D entry-point symbol other than "_c_int00" specified: "code_start" Thomas Wilk Prodigy150points Part Number:LAUNCHXL-F28377S Tool/software:Code Composer Studio I was following the instructions to write an LED blink program from the F28377S Us...