AAA記帳從未在錨點上完成,因此9800沒有記帳方法清單,而AireOS WLC將啟用記帳並指向ISE。 AireOS需要錨定在9800而不是它本身。在Policy Profile中,9800不會選擇錨點,但會選中Export Anchor框。 必須注意的是,當AireOS WLC將客戶端導出到9800時,沒有策略配置檔案的概念。它只傳送WLAN配置檔名稱...
Now that the policy set is configured, you need to inform ISE about the 9800 (foreign) in order for ISE to trust it as an authenticator. This can be done by navigating toAdmin > Network Resources > Network Device > +. You need to name it, set the IP a...
三个皮匠报告网提供Catalyst Wireless - 如何成功迁移到 Catalyst 9800.pdf这份报告的下载服务,该报告格式为PDF,页数为142,大小为6.72MB,分享用户为2200,欢迎用户下载使用
# Welcome to the Cisco Catalyst 9800-AP Embedded Wireless Controller command line interface. ## ## Please see command reference guide for the complete list of supported commands for this release: ## https://www.cisco.com/c/en/us/td/docs/wireless/embedded_wireless_controller_conf...
- Normally you should only have one active EWC controller on the network ; in that case client behavior can further be observed according to https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-9800-series-wireless-controllers/217738-monitor-catalyst-9800-kpis-key-performa....
您可以创建新配置或使用之前配置的。此时,取消选中Central Switching、Central Authentication、Central DHCP和Central Association Enable框。 第四步:策略标签配置. 关联已配置的WLAN和已创建的策略配置文件。 第五步:Flex配置文件配置。 创建Flex配置文件,导航到本地身份验证选项卡,配置Radiu...
您可以创建新配置或使用之前配置的.此时,取消选中Central Switching,Central Authentication,Central DHCP和 Central Association Enable框. 第四步:策略标签配置. 关联已配置的WLAN和已创建的策略配置文件. 第五步:Flex配置文件配置. 创建Flex配置文件,导航到本地身份验证选项卡,配置Radius服务器组并...
Check your 9800 WLC config withWireless Config Analyzerusing "show techwireless" output or "config paging disable" then "show run-config" output on AireOS and useWireless Debug Analyzerto analyze your WLC client debugs Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Conne...
在ISE上,您需要创建授权配置文件、带有身份验证策略的策略集和使用授权配置文件的授权策略,将9800(外部)作为网络设备添加到ISE,并创建用户名和密码以登录网络。 要创建授权配置文件,请导航到Policy > Policy Elements > Authorization > Results > Authorization Profiles,然后单击Add。确保返回的...
第四步:导航到Advanced选项卡,并启用Central Authentication Enable和Allow AAA Overrideoptions。必须禁用集中交换。 如果希望身份验证过程由9800 WLC集中执行,则必须启用集中身份验证。如果您希望FlexConnect AP对无线客户端进行身份验证,请禁用此功能。 CLI # config t ...