学习内容源自于cadence官方的教程“Virtuoso Analog Design Environment”,主要介绍了多个test(ADE L)选择、output skill语法、spec 范围判断语法、结果的比较和总结、变量的sweep、corner设置、parameter设置、蒙特卡洛仿真、还有一些杂七杂八的设置和debug。 SKILL 首先ADE最重要
model parameter:扫描工艺库模型文件中的参数:工艺库文件一般都由晶圆厂提供标准模型,所以一般不使用这项扫描功能。 窗口设置:Save DC Operating Point :保存直流工作点 Sweep Variable :对参数扫描 示例演示:以smic180mmf工艺库的共源级放大器为例 1.2 直流工作点仿真 电路 打开ADE,点击Stimuli设置激励源 VDD直流电压...
Cadence技术支持_原创精品文档.pdf,目录 在 ADE 中自动设置 SWEEP PARAMETER WITH CORNER ANALYSIS13 设置 Revise/Add Property Name through CDF Editor16 Measure DAC INL/DNL with Verilog-A Measure Cell in 电路图和Verilog module的混合仿真 Interrupt and Recovering
③选择分析类型.在 ADE 窗口中选 Analyses→Choose,就会弹出分析类型对话框(即 CA 窗口),然后选中 dc,Save DC Operating Points(为了方便观察管子的工作点而选),在 Sweep Variable 栏中选择 Design Variables,然后于 Variable Name 栏输入要扫描的变量 vin ,具体 设置如图 1.8 所示:(表示对 vin 做直流扫描,从 ...
1、目录在ade中自动设置modellibrary.3aboutspectreoutputformat.4aquestionaboutadelinebroken.5simulatewithnetlistusingspectreinade.7spectrearithmeticexception.8importcdl.9assignnetexpression.10transientnotconverge.11sweepparameterwithcorneranalysis.13设置corneranalysis.14multiplemodellibrary.15revise/addpropertynam 2、e...
I have a confusion about "parameters" and "variables" in Cadence ADE GXL. There are some variables which must satisfy the spec during the run (as an example vdd of 1.8 with 10%, three sweep 1.6, 1.8, 2.0; or bias current variation). Apart from that, there are some parameters which ...
2.1基本界面与操作主要介绍CadenceADE的主窗口与选项、设计库管理器、电路图编辑器、模拟设计环境和波形显示窗口。采用CadenceIC进行集成电路设计:将CadenceIC由系统管理员安装在Unix/Linux环境下,并完成配置文件基本设置。芯片设计——CMOS模拟集成电路设计与仿真实例:基于CadenceIC617第17页/共84页 2.1.1软件启动命令行...
在ADE中⾃动设置model library (3)About Spectre output format (4)A question about ADE – Line Broken (5)Simulate with netlist using spectre in ADE (7)spectre arithmetic exception (8)Import CDL (9)Assign Net Expression (10)Transient NOT Converge (11)SWEEP PARAMETER WITH CORNER ANALYSIS (13)...
②在 ADE 窗口中,选择 Analyses→Choose,打开 Choosing Analyses 窗口。 ③ 设置 Analyses 栏目中的 ac : a. 在 Analysis 里,选择 ac b. 设置 Sweep Variable 为 Frequency c. 设置 Sweep Rangs 为 Start-Stop,Start 赋值为 100,Stop 赋值为 150M d. 设置 Sweep Type 为 Logarithmic ,选择Points Per ...
Picture 6 - ADE Assembler Message 1921 FullscreencheckSysConf.cad-2021.07.10.14_50.17272.logDownload 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 === [Copyright 2002-2019] Cadence Design Systems, Inc. All righ...