px_uintt1,t2;for(inti=0;i<100;i++){t1=PX_TimeGetTimeUs();PX_Sleep(5);power_switch();...
cos i have been waiti cos i know i just can cos i never wanna see cos i still believe a cos living is so hard cos theres so many th cos youre here with m cosa nostra iv bar coscells coscinodiscus gigas coscinodiscus margina cosco hk cargo servic cosco henan intl frei cosco internat...
call up ring once han call waitingcall wait call you spell it call-exner body call- call-in medical care call-in-point callable bod callaeas cinerea callao stadt in peru callazantedeschia aet callback methods called a called a path cover called a tropical yea called advanced adeno called exc...
sys.wait(5000) --延时5S 延时函数一般配合任务使用 ?...一次性定时器 ?...5000:延时5S --最后一个参数:传给回调函数的参数 sys.timerStart(OneTimer,5000,"delay 5s") 程序启动延时5S后打印 ?...循环定时器 ?...end --循环定时器: sys.timerLoopStart --LoopTimer:回调函数 --1000:延时1S --最后...
[11/14/13 14:50:27.706 UTC 702f69 8528] Starting wait join timer for AP: 10.201.234.24:18759 [11/14/13 14:50:27.707 UTC 30e2 267] %DTLS: entering dtls_add_dtls_session_db_entry [11/14/13 14:50:27.707 UTC 30e3 267] %DTLS: sip = 0xac9ea04 dip = 0xac9ea18 ...
Linux中Sleep和Wait命令的使用方式 Sleep命令 sleep 命令会暂停指定的时间。它通常用于脚本中,但也适用于命令行。在下面的示例中, sleep 在两个 date 命令之间暂停30秒。...sleep 命令将数字参数作为秒数。...[root@localhost ~]# while true ; do free -h ; sleep 5 ; done Wait命令 wait 命令在等待后台...
ethernet link up, 100 mbps, full-duplex Ethernet port 0 initialized: link is up button is pressed, wait for button to be released..6 松开ap上的mode键，ap把自己的以太口设置为10.0.0.1的ip地址，然后广播去找tftp服务器下的c1601I-k9w7-tar.default镜像文件,更新时的屏幕显示如下extracti...
mode为 P_WAIT 表示在子程序运行完后返回本程序 P_NOWAIT 表示在子程序运行时同时运行本程序(不可用) P_OVERLAY表示在本程序退出后运行子程序 在spawn函数族中,后缀l、v、p、e添加到spawn后, 所指定的函数将具有某种操作能力 有后缀 p时, 函数利用DOS的PATH查找子程序文件 ...
Stopped OSWatcher TFA is running - Will wait 5 seconds (up to 3 times) TFA is running - Will wait 5 seconds (up to 3 times) TFA is running - Will wait 5 seconds (up to 3 times) TFAmain Force Stopped Successfully TFA Stopped Successfully . . . Successfully stopped TFA.. 查看安装...
After the isis timer lsp-retransmit command is run on a device, the device will wait retransmit-interval after having sent an LSP. If the device receives a PSNP from the other end, the device will not retransmit the LSP. Otherwise, the device will retransmit the LSP. If the value of ret...