px_uintt1,t2;for(inti=0;i<100;i++){t1=PX_TimeGetTimeUs();PX_Sleep(5);power_switch();...
call up ring once han call waitingcall wait call you spell it call-exner body call- call-in medical care call-in-point callable bod callaeas cinerea callao stadt in peru callazantedeschia aet callback methods called a called a path cover called a tropical yea called advanced adeno called exc...
cos i have been waiti cos i know i just can cos i never wanna see cos i still believe a cos living is so hard cos theres so many th cos youre here with m cosa nostra iv bar coscells coscinodiscus gigas coscinodiscus margina cosco hk cargo servic cosco henan intl frei cosco internat...
[11/14/13 14:50:27.706 UTC 702f69 8528] Starting wait join timer for AP: 10.201.234.24:18759 [11/14/13 14:50:27.707 UTC 30e2 267] %DTLS: entering dtls_add_dtls_session_db_entry [11/14/13 14:50:27.707 UTC 30e3 267] %DTLS: sip = 0xac9ea04 dip = 0xac9ea18 ...
sys.wait(5000) --延时5S 延时函数一般配合任务使用 ?...一次性定时器 ?...5000:延时5S --最后一个参数:传给回调函数的参数 sys.timerStart(OneTimer,5000,"delay 5s") 程序启动延时5S后打印 ?...循环定时器 ?...end --循环定时器: sys.timerLoopStart --LoopTimer:回调函数 --1000:延时1S --最后...
ethernet link up, 100 mbps, full-duplex Ethernet port 0 initialized: link is up button is pressed, wait for button to be released..6 松开ap上的mode键，ap把自己的以太口设置为10.0.0.1的ip地址，然后广播去找tftp服务器下的c1601I-k9w7-tar.default镜像文件,更新时的屏幕显示如下extracti...
(未超时)返回0,失败返回-1,超时返回-1并且errno = ETIMEDOUT...,不含写操作 * fd:文件描述符 * wait_seconds:等待超时秒数, 如果为0表示不检测超时; * 成功(未超时)返回0,失败返回-1,超时返回-1并且errno = ETIMEDOUT...,但出错的情况还是可以看到的,比如不要启动服务器端程序,而直接启动客户端程序,...
After the isis timer lsp-retransmit command is run on a device, the device will wait retransmit-interval after having sent an LSP. If the device receives a PSNP from the other end, the device will not retransmit the LSP. Otherwise, the device will retransmit the LSP. If the value of ret...
"-s,--seconds duration of test in seconds\n" "-b,--block block mode\n" "-p,--poll use poll (wait for event - reduces CPU usage)\n" "-e,--effect apply an effect (bandpass filter sweep)\n" ); printf("Recognized sample formats are:"); ...
mode为 P_WAIT 表示在子程序运行完后返回本程序 P_NOWAIT 表示在子程序运行时同时运行本程序(不可用) P_OVERLAY表示在本程序退出后运行子程序 在spawn函数族中,后缀l、v、p、e添加到spawn后, 所指定的函数将具有某种操作能力 有后缀 p时, 函数利用DOS的PATH查找子程序文件 ...