int p = bbuf.position(); int l = bbuf.limit(); // 回绕缓冲区 一是将 curPointer 移到 0, 二是将 endPointer 移到有效数据结尾 bbuf.flip(); byte[] byten = new byte[bbuf.limit()]; // 可用的字节数量 bbuf.get(byten, bbuf.position(), b
limit:buffer 中有效的数据长度大小; capacity:初始化时的空间容量。 以上四个基本属性的关系是:mark <= position <= limit <= capacity。 他有以下问题: 第一,ByteBuffer 分配的长度是固定的,无法动态扩缩容,所以很难控制需要分配多大的容量。如果分配太大容量,容易造成内存浪费;如果分配太小,存放太大的数据会抛...
ByteBuffer 读模式 写模式 在读模式下,从头开始读取数据,直到limit代表数据读取完成,capacity代表容量 在写模式下,position移到数据终点位置,limit移到capacity位置,数据从position位置开始写,直到limit(capacity)位置,停止写入。 ByteBuf 主要通过两个index:readindex和writeindex来完成数据的读写,整个缓冲区分为三个部分:...
byte[] bytes = new byte[buffer.limit()]; buffer.get(bytes); return bytes; } } 上述代码其实就是根据给定的编码方式进行编码。如果调用的是不带参数的getBytes()方法,则使用默认的编码方式,如下代码所示: 1 2 3 4 5 6 7 8 9 10 11 /** * JDK source code */ private static Charset getDefault...
因此,当切换Buffer到读模式时,limit会被设置成写模式下的position值。即你能读到之前写入的所有数据(limit被设置成已写数据的数量,这个值在写模式下就是position)。 4 Buffer的类型 Java NIO Buffer有如下类型 这些Buffer类型代表了不同的数据类型,即可通过这些类型来操作缓冲区中的字节。
nio的接口中,基本都是使用ByteBuffer进行操作,个人使用体验来看,ByteBuffer的limit机制灵活程度更高,至于效率我没有做过测试不好发言。其次就是可以兼顾到堆外内存,一般在使用java做一些中间件涉及到存储的时候基本都会使用到ByteBuffer 发布于 2016-12-31 12:21 赞同1添加评论 分享收藏喜欢收起...
Since: 1.1 See Also: InputStream.mark(int) InputStream.reset() mark public void mark(int readAheadLimit) Set the current marked position in the stream. ByteArrayInputStream objects are marked at position zero by default when constructed. They may be marked at another position within the buffer...
JIT compilerstend to focus on the simpler forms of targetcode improvement. Specifically, they often limit themselves to so-calledlocalimprovements, which operate within individualcontrol flow constructs. Improvements at theglobal(whole method) andinterprocedural(whole program) level are usually too ...
where0<=n<=r. This byte sequence will be transferred from the buffer starting at indexp, wherepis the buffer's position at the moment this method is invoked; the index of the last byte written will bep+n-1. Upon return the buffer's position will be equal top+n; its limit will not...
64-bit IIS memory limit !!! 999 non standard linked in error A blocking operation was interrupted by a call to WSACancelBlockingCall A call to PInvoke function has unbalanced the stack. This is likely because the managed PInvoke signature does not match the unmanaged target signature. (.NET ...