The BFD priority on an interface is higher than the BFD priority on a RIP process. If the rip bfd block command is configured on an interface, the bfd all-interfaces enable command cannot be used to enable BFD on the interface. Example # Enable BFD on all interfaces in a RIP process....
If the rip bfd block command is configured on an interface, the bfd all-interfaces enable command cannot be used to enable BFD on the interface. Example # Enable BFD on all interfaces in a RIP process. <HUAWEI> system-view [HUAWEI] bfd [HUAWEI-bfd] quit [HUAWEI] rip [HUAWEI-rip...
[AR2-GigabitEthernet0/0/0]undo shutdown3、故障切换场景二，OSPF联动BFD，在R2接口G0/0/0和G0/0/1全部down模拟网络故障故障切换钱我们提前把R4的G0/0/2接口OSPF值改为200，R4优先走R2到R1interface GigabitEthernet0/0/2ospf cost 200 //默认为1改为200此时R4设备路由表可以看出优先从R2到R1 模拟故障：[...
6、 0.0.0.0 bfd all-interface enableOSPF neighborG0/0/1G0/0/1RTARTDSWBSWCBFD与VRRP联动配置需求RTCRTASWARTB主出口SWB主网关SWCVRRPPC-APC-BPC-C场景需求如图,SWA和SWB为VRRP备份组,SWB为主用。当RTB与RTC的互联链路出现故障时,SWB能够快速感知并切换为备用网关状态,且SWA成为主用网关。BFD与VRRP联动配置实...
Enable special processing for BFD sessions. bfd detect-interface special-processing [ admin-down | authentication-change | session-up ] * By default, all types of special processing are disabled for BFD sessions. Associating two static BFD sessions About this task This task enables the state of ...
Device>enable Enables privileged EXEC mode. Enter your password if prompted. Step 2 configureterminal Example: Device#configure terminal Enters global configuration mode. Step 3 interfacetype number Example: Device(config)#interface serial 2/0
Enable special processing for BFD sessions. bfd detect-interface special-processing [ admin-down | authentication-change | session-up ] * By default, all types of special processing are disabled for BFD sessions. Configuring the TTL value for BFD packets About this task When you connect an H3C...
Switch(config)#interface ethernet 1/1 Switch(config-if)#mtu 9216 1. 2. Nexus 2000 配置 注意,Nexus 2000 MTU 配置需要在其父 FEX 交换机上进行配置,如果父交换机支持接口下配置MTU,则在对应接口下配置,如果不支持,则需要使用network-qos。 需要注意,使用 FEX 时,Fabric Port Channel (FPC) ,也就是连接...
interface GigabitEthernet0/0/4 ip address 222.222.222.2 255.255.255.252 # interface LoopBack1 description guanli-to-S1 alias LoopBack1 ip address 9.9.9.1 255.255.255.0 # firewall zone trust set priority 85 add interface GigabitEthernet0/0/0 ...
[*SwitchB-ospf-1] bfd all-interfaces enable [*SwitchB-ospf-1] quit [*SwitchB] commit 配置接口的BFD特性 #在SwitchA接口VLANIF10上配置BFD特性,并指定最小发送和接收间隔为100ms,本地检测时间倍数为4。 [~SwitchA] interface vlanif 10 [~SwitchA-Vlanif10] ospf bfd enable ...