下面的示例将默认路由添加到在步骤 1 中创建的路由表。 唯一支持的路由是“0.0.0.0/0”到“VPN 网关”下一跃点的目标前缀。 PowerShell Get-AzureRouteTable-Name"MyRouteTable"|Set-AzureRoute–RouteTable"MyRouteTable"–RouteName"DefaultRoute"–Address
采用ExpressRoute 连接的站点到站点连接 添加或移除站点到站点连接 强制隧道 配置自定义 IPsec/IKE 连接策略 修改本地网关 VPN 设备 点对站点(P2S)VPN VNet 到 VNet VPN 安全性 路由 监控 故障排除 参考 资源 Learn 蔚蓝 网络 VPN 网关 使用英语阅读
依預設,Azure 會將 GatewaySubnet 首碼範圍中的私人 IP 位址自動指派為 VPN 閘道上的 Azure BGP IP 位址。 當內部部署 VPN 裝置使用 APIPA 位址 (169.254.0.1 到 169.254.255.254) 作為 BGP IP 時,需要自訂 Azure APIPA BGP 位址。 如果對應的區域網路閘道資源 (內部部署網路) 具有作為 BGP 對等體 IP 的...
建立和管理 VPN 閘道 站對站 使用ExpressRoute 連線的站對站 VNet 對 VNet 點對站 管理閘道 SKU 路由、BGP 及 VNet 對等互連 設定VPN 閘道的 NAT 修改區域網路閘道 設定VPN 裝置 設定自訂的 IPsec/IKE 連線原則 設定主動-主動閘道 設定區域備援閘道 ...
Connect your infrastructure to the cloud with Azure VPN Gateway. Connect your on-premises networks to Azure from anywhere with Site-to-Site VPNs.
Connect your infrastructure to the cloud with Azure VPN Gateway. Connect your on-premises networks to Azure from anywhere with Site-to-Site VPNs.
访问Vnet1和Vnet2所有地址段: Next Hop:IDC Edge Route(本地需配置往Azure网段路由发往ExpressRoute Private Peering Tunnel即可) Gateway Subnet 路由表RT GW: IDC所有地址段回包Vnet1/subnet1:无需额外配置,靠Vnet Peering可回包 IDC所有地址段回包Vnet1/subnet2以及Vnet2所有subnets:Next Hop: NVA FW,之后由...
由于在Vnet Peering配置中,Vnet-BGP-1可以使用远端的Gateway,所以远端的Gateway就相当于本地的Gateway使用。 在Vnet-BGP-1的vlan1中,关联如下的Route-Table: 这个路由表中,10.3.0.0/16是Vnet-BGP-3的网段,下一跳是VPN Gateway,这个VPN Gateway是在Vnet-BGP-2网络中的。虽然Vnet-BGP-1和Vnet-BGP-3是不通的,...
nameif vti-vpn-2-40.65.166.197 ip address 10.0.1.241 255.255.255.252 #It should be within the 'GatewaySubnet' in Azure 这个没问题, tunnel source interface outside tunnel destination 40.65.166.197 tunnel mode ipsec ipv4 tunnel protection ipsec profile Azure-Ipsec-PROF-vpn-2-40.65.166.197 ...
點對站 (P2S) VPN 關於點對站 VPN 關於點對站 VPN 路由 設定P2S - 憑證驗證 設定P2S - Microsoft Entra ID 驗證 設定P2S - RADIUS 驗證 設定Always On 通道 從SSTP 移至 OpenVPN 或 IKEv2 P2S 工作階段管理 將自訂路由公告至 P2S 用戶端 建立P2S 的自訂 IPsec 原則 ...