该板设计为由 12v DC(通过 2x20p 接头上的 VIN 引脚)供电,该电压通过 LDO 稳压器在内部调节至 5v。 外部3.3v 也应提供给 2x20Pin 接头,以启用同一接头上的 I2C 电平转换器。在这个版本的 PCB 中,I2C 没有直接连接到 PCB 上。 还提供了一个复位按钮和电源 LED,以及 D13 上的标准 LED。 代码 编码说明...
ATMEGA328P-MU Datasheet PDF ATMEL RISC Microcontroller, 8Bit, FLASH, AVR RISC CPU, 20MHz, CMOS, PQCC32, 5 X 5MM, 1MM HEIGHT, 0.5MM PITCH, GREEN, PLASTIC, MO-220VHHD-2, MLF-32 ATMEGA328-AU Datasheet PDF Microchip MCU 8Bit AVR RISC 32KB Flash 2.5V/3.3V/5V 32Pin TQFP Tray ...
UNO-R3开发板官方版本兼容ATmega328P单片机模块 深圳市多微斯科技有限公司10年 月均发货速度:当日 广东 深圳市 ¥29.00成交24182个 UNOR3官方版开发板atmega328p芯片单片机模块兼容arduino编程主板 深圳市华宇芯科技有限公司4年 月均发货速度:暂无记录 广东 深圳市龙岗区 ...
原装正品 ATMEGA328P-AU ATMEGA328P 贴片TQFP-32 8位微控制器 杭州一路发发跨境电子商务有限公司1年 月均发货速度:暂无记录 浙江 杭州市 ¥11.00 全新原装ATMEGA328P-AU 微控制器 封装TQFP32 量大价优 深圳市福田区芯港微电子商行9年 月均发货速度:暂无记录 ...
Samacsys Description: ATMEGA328P-MU, 8 bit AVR Microcontroller 20MHz 1, 32kb Flash, 2kb RAM, I2C SPI 32-Pin MLF 具有ADC: YES 其他特性: ALSO OPERATES AT 2.7 V MINIMUM SUPPLY AT 10 MHZ AND 1.8 V MINIMUM SUPPLY AT 4 MHZ 地址总线宽度: 位大小: 8 CPU系列: AVR RISC 最大时钟频率: 20...
How to load locked program in smd 328p 32 Pin. Reply DuckDaffy These solutions may help you too. AVR HV Rescue Shield 2: https://mightyohm.com/blog/products/hv-rescue-shield-2-x/ HVPP (High Voltage Parallel Programming) is possible on HW 1.x and 2.x. ...
ATmega328P 8 位 megaAVR picoPower 微控制器 Atmel ATmega328P 微控制器是基于 AVR 增强型 RISC 体系架构的 8 位 megaAVR 设备。 其特色为 picoPower 技术,可提供超低功耗和低功率睡眠模式,非常适合用于电池供电型应用。 ### 微控制器功能 20 MHz 最大工作频率 20 MHz 时高达 20 MIPS 32 KB...
Before direct plug into the female pin-headers, please verify if the RGB dot matrix are proven compatible. The concern is mainly on the pin out, where same color LEDs are in cluster, here we attach the scheme and photo demonstration. The color sequence might change, since the controlling ...
ATMEGA328P is high performance, low power controller from Microchip. ATMEGA328P is an 8-bit microcontroller based on AVR RISC architecture. It is the most popular of all AVR controllers as it is used in ARDUINO boards. ATMega328 Pinout Configuration ATMEGA328P is a 28 pin chip as shown in...
(If you're not planning to use the bootloader (uploading code using a USB to serial adapter), the FTDI header and the 100 nF capacitor on the reset pin can be omitted.) Open theTools > Boardmenu item, selectMiniCoreand select your preferred target. ...