上面的启动过程是qsdk的,在Openwrt中并没有这么多的文件,只有board-2.bin,board.bin,firmware-5.bin,其中board.bin还是一个空文件(文件实际上是一串ASCII文本“../../cal-pci-0000:01:00.0.bin”),那么这些固件是怎么加载的呢? 上面的启动过程是qsdk的,在Openwrt中并没有这么多的文件,只有board-2.bin,boa...
然后将该文件复制为固件-2.bin到ath10k固件目录: cp固件-2.bin_10.1.467.2-1 ath10k，然后重新加载...
ath10k/cal-pci-0000:02:00.0.bin (-2) [ 708.803719] ath10k_pci 0000:02:00.0: firmware: failed to load ath10k/QCA6174/hw2.1/firmware-6.bin (-2) [ 708.803887] ath10k_pci 0000:02:00.0: firmware: direct-loading firmware ath10k/QCA6174/hw2.1/firmware-5.bin ...
The `Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2` and `otp stream is empty, using board.bin contents` are expected. These are due to the fact OpenWRT had a custom patch for loading chip calibration data off of flash partition (instead of on-chip EEPR...
Direct firmware load for ath10k/cal-pci-0000:05:00.0.bin failed with error -2 977 [516861.779600] ath10k_pci 0000:05:00.0: fwcfg key: vdevs val: 64 978 [516861.779601] ath10k_pci 0000:05:00.0: fwcfg key: peers val: 128 979 [516861.779603] ath10k_pci 0000:05:00.0: fwcfg key: activ...
[3538979.052001] ath10k_pci 0000:07:00.0: ATH10K_END This can be used to debug firmware issues, but in systems that are not having any trouble, users may want to disable it. To do so, set flag 0x10000000 in the ath10k debug_level setting. This can be done by echoing a value to the...
[ 28.365087] ath10k_pci 0000:01:00.0: [03]: 0x0004ac00 2 2 3 2 [ 28.369483] ath10k_pci 0000:01:00.0: [04]: 0x0004b000 0 0 40 0 [ 28.378177] ath10k_pci 0000:01:00.0: [05]: 0x0004b400 1 1 0 1 [ 28.382330] ath10k_pci 0000:01:00.0: [06]: 0x0004b800 0 0 0 0 [ 28....
[ 3010.744628] ath10k_ahb a800000.wifi: ath10k_pci ATH10K_DBG_BUFFER: [ 3010.752811] ath10k: [0000]: 001586DB 10045881 00003112 0041CDAC 0000000A 00000000 001586DC 10045881 [ 3010.759058] ath10k: [0008]: 00003112 0041CDAC 0000000E 00000000 001586FE 10085881 00003112 0041CCBC ...
[ 16.035965] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 16.121972] ath: EEPROM regdomain sanitized [ 16.121981] ath: EEPROM regdomain: 0x64 [ 16.121985] ath: EEPROM indicates we should expect a direct regpair map [ 16.12...
14:26 2024 kern.info kernel: [ 21.391723] ath10k_pci 0000:00:00.0: wmi print 'free: 114572 iram: 12644 sram: 29508' Sat Dec 7 10:14:26 2024 kern.info kernel: [ 21.629032] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto ...